Home › Engine / Hybrid System › 3UR-FBE LUBRICATION › OIL AND OIL FILTER
RM27M0U _51 Engine / Hybrid System _049116 3UR-FBE LUBRICATION _0234078 OIL AND OIL FILTER A

3UR-FBE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

a.
A150108

Remove the 3 screws and 5 bolts.


b.

Unhook the engine under cover from the vehicle body as shown in the illustration.


Hide 3.REMOVE OIL FILTER ELEMENT

a.
A380063E02
2.333,1.479 2.719,1.115 false 0.927,0.604 1.365,0.354 false 2.781,1 3.156,1.188 0.375,0.188 10 false Hose 1.438,0.24 1.813,0.427 0.375,0.188 10 false Pipe

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A162459

Remove the oil filter drain plug.


c.
A162460E03
2.594,2.292 2.76,1.26 2.76,1.26 2.875,1.26 false 2.063,1.896 2.333,0.896 2.333,0.896 2.49,0.896 false 2.792,2.781 2.792,3.042 false 2.646,2.75 1.521,2.75 false 1.531,2.313 1.75,2.313 1.75,2.313 2.885,2.615 false 1.521,3.094 1.74,3.094 1.74,3.094 2.844,2.906 false 2.531,0.802 2.885,0.99 0.354,0.188 10 false Cap 2.906,1.177 3.323,1.385 0.417,0.208 10 false Valve 1.125,2.208 1.5,2.406 0.375,0.198 10 false Pipe 1.031,2.646 1.49,2.875 0.458,0.229 10 false O-Ring 1.115,2.99 1.469,3.177 0.354,0.188 10 false Hose

Install the pipe to the oil filter cap.

HINT:

Use a container to catch the draining oil.


NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.



d.
A162461

Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.


e.
A178490E04
1.771,0.969 2.313,0.969 true 2.104,2.5 2.396,2.5 true 0.896,1.125 1.042,1.125 1.042,1.125 1.26,1.323 false 1.594,2.76 0.844,2.76 true 0.052,0.094 1.198,0.313 1.146,0.219 12 false w/o Oil Cooler: 0.083,1.646 1.094,1.875 1.01,0.229 12 false w/ Oil Cooler: 0.51,1.031 0.896,1.302 0.385,0.271 10 false SST 0.5,2.688 0.802,2.875 0.302,0.188 10 false SST 2.354,0.885 3.198,1.552 0.844,0.667 10 false Oil Filter Bracket Clip 2.417,2.417 3.26,3.083 0.844,0.667 10 true Oil Filter Bracket Clip

Using SST, remove the oil filter cap.

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip.



f.
U151582E02
1.729,1.833 1.344,1.833 false 1.75,2.948 1.75,2.302 1.75,2.302 1.406,2.302 false 1.75,2.302 2.042,2.302 false 1.99,0.063 3.094,0.458 1.104,0.396 12 false w/ Oil Cooler: 0.167,0.063 1.344,0.448 1.177,0.385 12 false w/o Oil Cooler: 1.896,1.031 3.01,1.198 1.115,0.167 10 false Oil Filter Element 1.563,2.969 2.031,3.177 0.469,0.208 10 false O-Ring

Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



Hide 4.INSTALL OIL FILTER ELEMENT

a.
U151582E02
1.729,1.833 1.344,1.833 false 1.75,2.948 1.75,2.302 1.75,2.302 1.406,2.302 false 1.75,2.302 2.042,2.302 false 1.99,0.063 3.094,0.458 1.104,0.396 12 false w/ Oil Cooler: 0.167,0.063 1.344,0.448 1.177,0.385 12 false w/o Oil Cooler: 1.896,1.031 3.01,1.198 1.115,0.167 10 false Oil Filter Element 1.563,2.969 2.031,3.177 0.469,0.208 10 false O-Ring

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.


c.

Set a new oil filter element to the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.
A178489E04
1.781,1 2.323,1 false 2.115,2.531 2.406,2.531 false 0.896,1.156 1.052,1.156 1.052,1.156 1.26,1.323 false 1.594,2.76 0.844,2.76 true 0.083,0.031 1.208,0.281 1.125,0.25 12 false w/o Oil Cooler: 0.073,1.719 1.125,1.938 1.052,0.219 12 false w/ Oil Cooler: 0.521,1.073 0.833,1.26 0.313,0.188 10 false SST 0.49,2.688 0.802,2.865 0.313,0.177 10 false SST 2.365,0.927 3.208,1.281 0.844,0.354 10 false Oil Filter Bracket Clip 2.417,2.448 3.323,3.208 0.906,0.76 10 true Oil Filter Bracket Clip

Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

When tightening the oil filter cap, do not remove the oil filter bracket clip.

·

Make sure that the oil filter is installed securely as shown in the illustration.

·

Be careful that the O-ring does not get caught between any surrounding parts.




g.
A162466E04
2.656,2.74 1.333,2.74 false 0.854,2.625 1.313,2.823 0.458,0.198 10 false O-Ring

Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between any surrounding parts.



Hide 5.ADD ENGINE OIL

a.

Add fresh oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
ILSAC GF-5 multigrade engine oil 0W-20


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 7.1 liters (7.5 US qts, 6.2 Imp. qts)
Drain and refill with oil filter change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
Dry fill 9.3 liters (9.8 US qts, 8.2 Imp. qts)



b.

Install the oil filler cap.


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER

a.
A150108

Hook the engine under cover to the vehicle body as shown in the illustration.


b.

Install the 3 screws and 5 bolts.

Torque:
for bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for screw : 5.4 N*m (55 kgf*cm, 48 in.*lbf)