41400
1.REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR
Remove the 4 bolts.
Using a hammer handle, remove the actuator.
41320
2.REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY
Remove the 4 bolts.
Using a plastic-faced hammer, remove the differential tube.
41304P
3.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
Using SST, tap out the oil seal.
41306F
4.REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY
Using SST, remove the side gear inter shaft.
| *a | Turn |
| *b | Hold |
Remove the snap ring from the side gear inter shaft.
41204E
5.REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT
Using SST and a hammer, unstake the nut.
Using SST to hold the companion, remove the nut.
41204D
6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, remove the companion flange from the differential carrier.
| *a | Turn |
| *b | Hold |
41101D
7.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL
Using SST, remove the oil seal.
41214C
8.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41141L
9.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER
Remove the bolts B and front differential front support assembly LH.
Remove the bolts A.
Using a plastic-faced hammer, tap out the bearing retainer.
10.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case from the differential carrier.
11.REMOVE DIFFERENTIAL DRIVE PINION
Set the differential carrier to an overhaul stand as shown in the illustration.
| *a | Block |
Using a press, press out the drive pinion.
Do not drop the drive pinion.
41211B
12.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
Remove the bearing (inner race) from the differential carrier.
41231F
13.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
41183C
14.REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR
Remove the 2 bolts and oil deflector.
41110V
15.REMOVE FRONT DIFFERENTIAL UNION
Remove the front differential union from the differential carrier.
41211A
16.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a press, press out the bearing (inner race).
If the drive gear or ring gear is damaged, replace them as a set.
41211A
17.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using a brass bar and hammer, tap out the bearing (outer race) and washer.
41211B
18.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
Using SST and hammer, tap out the bearing (outer race).
41311A
19.REMOVE FRONT DIFFERENTIAL CASE BEARING
Measure the plate washer and note its thickness.
Tag the bearing outer races to show the location for reassembly.
Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.
| *1 | Plate Washer |
Using SST and a press, press out the bearing (outer race) and plate washer from the differential carrier.
| *1 | Plate Washer |
20.REMOVE DIFFERENTIAL RING GEAR
Place matchmarks on the ring gear and differential case.
| *a | Matchmark |
Remove the 12 bolts.
Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.
41311A
21.REMOVE FRONT DIFFERENTIAL CASE BEARING
Using SST, remove the 2 bearings (inner race).
Fix the claws of SST into the notch in the differential case assembly.
22.DISASSEMBLE DIFFERENTIAL CASE
Using a pin punch and hammer, tap out the straight pin.
Remove these parts from the differential case assembly.
2 differential side gears
2 differential side gear thrust washers
Differential pinion shaft
2 differential pinion gears
2 differential pinion gear thrust washers
41039A
23.INSPECT DIFFERENTIAL GEAR KIT
Check that there is no damage to the pinion gear and side gear.
If the pinion gear and/or side gear is damaged, replace the differential gear kit.
41311
24.INSPECT FRONT DIFFERENTIAL CASE
Check that the differential case is not damaged.
If the differential case is damaged, replace it.
41331G
25.REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING
Using a brass bar and hammer, tap out the 2 bearings.
41434
26.REMOVE DIFFERENTIAL CLUTCH HUB
Remove the differential clutch sleeve.
Using a snap ring expander, remove the snap ring.
Remove the differential clutch hub.
41304P
27.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
Using SST, tap out the oil seal.
41304F
28.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
Using a snap ring expander, remove the snap ring.
Using a plastic-faced hammer, tap out the side gear shaft.
41311A
29.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING
Using a snap ring expander, remove the snap ring.
Using SST, a brass bar and press, press out the bearing.
Do not damage the bearing.
30.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB
Check for wear and damage to the clutch hub and clutch sleeve.
If necessary, replace them.
Check that the clutch sleeve slides smoothly on the clutch hub.
31.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT
Check for wear and damage to the clutch hub and side gear inter shaft.
Check that the clutch sleeve slides smoothly on the side gear inter shaft.
41433
32.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE
Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.
0.35 mm (0.0138 in.)
If the clearance exceeds the maximum, replace the fork or clutch sleeve.