Home › Engine / Hybrid System › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY(for 1UR-FE)
RM27M0U _51 Engine / Hybrid System _049121 DIFFERENTIAL _0234098 DIFFERENTIAL CARRIER ASSEMBLY(for 1UR-FE) A

DIFFERENTIAL  DIFFERENTIAL CARRIER ASSEMBLY(for 1UR-FE)  DISASSEMBLY  


PROCEDURE

Hide 41204 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
F001237E33
2.271,1.844 2.583,2.042 0.313,0.198 10 false *a

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Text in Illustration
*a 72 mm (2.83 in.)

Maximum runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C159768

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C028211

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00788 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.


Hide 4.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

a.
C159766

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the case.

Standard backlash:

0.15 mm (0.00591 in.) or less


If the backlash is not as specified, replace the side gear thrust washer with one of a different thickness.


Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C124126

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard drive pinion preload (at starting):

0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 6.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

Standard drive pinion preload plus 0.24 to 0.46 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204B 7.REMOVE REAR DRIVE PINION NUT

a.
F044346E10
2.365,1.01 2.688,1.167 0.323,0.156 10 false SST

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
C124130E03
2.448,0.656 2.948,0.344 false 2.979,0.219 3.25,0.375 0.271,0.156 10 false SST

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
U152379E01
1.25,1.167 0.938,0.417 false 0.479,0.333 0.927,0.521 0.448,0.188 10 false SST 3.083,0.802 3.26,0.979 0.177,0.177 10 false *a 0.198,1.688 0.375,1.865 0.177,0.177 10 false *b

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09956-03030)
09955-03050  

Text in Illustration
*a Turn
*b Hold


Hide 41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C162373E03
1.469,0.802 1.156,0.646 false 0.885,0.542 1.177,0.698 0.292,0.156 10 false SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C124133E04
1.667,0.74 0.99,0.51 false 0.698,0.406 0.99,0.552 0.292,0.146 10 false SST

Using SST, remove the bearing (inner race).

SST
09556-22010  


b.

Remove the bearing spacer.


Hide 41316 12.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C159769

Remove the 2 bolts and 2 nut locks.


Hide 41311J 13.REMOVE REAR DIFFERENTIAL CASE ASSEMBLY

a.
C159776E04
1.552,1.24 1.25,1.719 1.25,1.719 1.552,1.323 false 1.156,1.719 1.417,1.906 0.26,0.188 10 true *a

Place matchmarks on the bearing cap and differential carrier.

Text in Illustration
*a Matchmark


b.

Remove the 4 bolts and 2 differential bearing caps.


c.
C028220

Remove the differential case from the differential carrier.

HINT:

Tag the 2 case bearing outer races to show the location for reassembly.



Hide 14.REMOVE REAR DIFFERENTIAL DRIVE PINION

a.
C030540

Remove the differential drive pinion and bearing spacer from the differential carrier.


Hide 41201A 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C294202E04
2.854,0.969 2.729,0.969 2.729,0.969 2.729,1.406 false 1.167,1.948 1.052,1.948 1.052,1.948 0.948,1.646 false 2.885,0.896 3.208,1.073 0.323,0.177 10 false SST 1.208,1.865 1.531,2.042 0.323,0.177 10 false SST

Using SST and a press, press out the bearing (inner race).

SST
09950-00020  

If either the drive pinion or ring gear is damaged, replace them as a set.


Hide 41201D 16.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 41201B 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C091046

Using a brass bar and hammer, tap out the bearing (outer race).

If the bearing is damaged during removal, replace it.


Hide 41201A 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C091047

Using a brass bar and hammer, tap out the bearing (outer race).

If the bearing is damaged during removal, replace it.


Hide 19.REMOVE DIFFERENTIAL RING GEAR

a.
C159770E04
1.896,1.542 2.344,1.719 false 2.385,1.646 2.583,1.802 0.198,0.156 10 false *a

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Remove the 12 ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 41311J 20.INSPECT REAR DIFFERENTIAL CASE ASSEMBLY RUNOUT

HINT:
C159746

If the ring gear runout is within the specified value (see "INSPECT RUNOUT OF DIFFERENTIAL RING GEAR" procedure), this inspection is not necessary.


a.

Install the differential case to the differential carrier.


b.

Inspect the differential case runout.

Maximum runout:

0.04 mm (0.00157 in.)



c.

Remove the differential case from the differential carrier.


Hide 41301A 21.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C159771E01
1.022,1.391 1.917,1.893 1.917,1.893 1.533,1.348 false 1.957,1.85 2.282,2.004 0.325,0.154 10 SST

Using SST, remove the 2 bearings.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00480)

HINT:

Fix the claws of SST to the notches in the differential case.



Hide 22.DISASSEMBLE DIFFERENTIAL CASE

a.
C159772

Using a pin punch and hammer, tap out the straight pin.


b.

Remove the pinion shaft, 2 pinion gears, 2 pinion gear thrust washers, 2 side gears and 2 side gear thrust washers.


Hide 41196 23.REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER (for Regular Cab Standard Deck)

a.
C160325

Remove the bolt, washer and dynamic damper.