Home › Engine / Hybrid System › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY(for 3UR-FE, 3UR-FBE)
RM27M0U _51 Engine / Hybrid System _049121 DIFFERENTIAL _0234103 DIFFERENTIAL CARRIER ASSEMBLY(for 3UR-FE, 3UR-FBE) A

DIFFERENTIAL  DIFFERENTIAL CARRIER ASSEMBLY(for 3UR-FE, 3UR-FBE)  DISASSEMBLY  


PROCEDURE

Hide 41204 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
F001237E25
2.281,1.844 2.49,2.01 0.208,0.167 10 false *a

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Text in Illustration
*a 72 mm (2.83 in.)

Maximum runout:
Runout Standard Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161428

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161429

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.


Hide 4.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

a.
C159766

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the case.

Standard backlash:

0.15 mm (0.00591 in.) or less


If the backlash is not within the specification, replace the side gear thrust washer with one of a different thickness.


Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C124126

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard drive pinion preload (at starting):

1.62 to 2.25 N*m (17 to 22 kgf*cm, 15 to 19 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 6.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

Standard drive pinion preload plus 0.19 to 0.38 N*m (2 to 3 kgf*cm, 2 to 3 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204B 7.REMOVE REAR DRIVE PINION NUT

a.
F044346E11
2.365,1.021 2.688,1.177 0.323,0.156 10 false SST

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
C124130E05
2.448,0.656 3.063,0.333 false 3.094,0.229 3.417,0.396 0.323,0.167 10 false SST

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
U152379E01
1.25,1.167 0.938,0.417 false 0.479,0.333 0.927,0.521 0.448,0.188 10 false SST 3.083,0.802 3.26,0.979 0.177,0.177 10 false *a 0.198,1.688 0.375,1.865 0.177,0.177 10 false *b

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09956-03030)
09955-03050  

Text in Illustration
*a Turn
*b Hold


Hide 41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C162373E04
1.469,0.805 1.154,0.645 false 0.768,0.538 1.063,0.690 0.295,0.152 10 SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C186906E01
2.397,1.202 1.879,0.635 false 2.49,1.05 2.058,0.638 false 2.383,0.807 2.198,0.634 2.198,0.634 1.765,0.634 false 1.393,0.554 1.701,0.710 0.309,0.156 10 SST

Using SST, remove the bearing (inner race).

SST
09950-40011  (09951-04010, 09953-04020, 09952-04010)
09955-04130  
09958-04020  


b.

Remove the 2 preload adjusting shims.


Hide 41311J 12.REMOVE REAR DIFFERENTIAL CASE ASSEMBLY

a.
C161430E03
1.542,1.26 1.115,1.729 1.115,1.729 1.552,1.323 false 0.979,1.667 1.25,1.875 0.271,0.208 10 true *a

Place matchmarks on the bearing cap and differential carrier.

Text in Illustration
*a Matchmark


b.

Remove the 4 bolts and 2 differential bearing caps.


c.
C124135E02
1.55,0.566 2.196,0.269 false 2.227,0.146 2.617,0.311 0.390,0.165 10 SST

Using SST and a plastic-faced hammer, remove the 2 plate washers.

SST
09504-22012  

HINT:

Measure the plate washer thickness and note it down.



d.

Remove the differential case with the bearing outer races from the carrier.

HINT:

Tag the bearing outer races to show the location for reassembling.



Hide 13.REMOVE REAR DIFFERENTIAL DRIVE PINION

a.
C030540

Remove the differential drive pinion and bearing spacer from the differential carrier.


Hide 41201A 14.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C294202E05
2.854,0.969 2.729,0.969 2.729,0.969 2.729,1.406 false 1.167,1.948 1.052,1.948 1.052,1.948 0.948,1.646 false 2.885,0.896 3.208,1.073 0.323,0.177 10 false SST 1.208,1.854 1.531,2.031 0.323,0.177 10 false SST

Using SST and a press, press out the bearing (inner race).

SST
09950-00020  

If either the drive pinion or ring gear is damaged, replace them as a set.


Hide 41201D 15.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C186907E01
1.029,1.012 0.827,0.772 0.827,0.772 0.586,0.772 false 0.242,0.686 0.870,0.994 0.628,0.309 10 SST

Using SST, remove the bearing (outer race).

SST
09308-00010  

If the bearing is damaged during removal, replace it.


Hide 41115 17.REMOVE DIFFERENTIAL OIL STORAGE RING

a.
C161484

Using a brass bar and hammer, tap out the storage ring.


Hide 41201A 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C161485

Using a brass bar and hammer, tap out the bearing (outer race).

If the bearing is damaged during removal, replace it.


Hide 19.REMOVE DIFFERENTIAL RING GEAR

a.
U152278E02
1.896,1.552 2.344,1.729 false 2.396,1.646 3.313,1.927 0.917,0.281 10 true *a

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Remove the 12 ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 41301A 20.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C186908E01
1.281,1.205 0.783,0.488 false 1.29,0.633 1.172,0.489 1.172,0.489 0.519,0.489 false 1.12,1.205 0.61,0.496 false 0.146,0.408 0.446,0.573 0.300,0.165 10 SST

Using SST, remove the 2 bearings.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09950-60010  (09951-00500)
09955-04120  

HINT:

Fix the claws of SST to the notches in the differential case.



Hide 21.DISASSEMBLE DIFFERENTIAL CASE

a.
C159772

Using a pin punch and hammer, tap out the straight pin.


b.

Remove the pinion shaft, 2 pinion gears, 2 pinion gear thrust washers, 2 side gears and 2 side gear thrust washers.


Hide 41196 22.REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER (for Regular Cab Standard Deck)

a.
C160325

Remove the bolt, washer and dynamic damper.