Home › Brake › BRAKE › BRAKE PEDAL
RM27M0U _54 Brake _049123 BRAKE _0234115 BRAKE PEDAL N

BRAKE  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 47101 1.CHECK BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Remove the tibia pad.


iii.
C208542E02
2.271,2.302 1.542,2.833 1.542,2.833 1.385,2.833 false 1.792,3.635 1.063,3.635 false 1.885,3.354 1.406,3.354 1.406,3.354 1.406,3.635 false 0.281,2.74 1.385,2.958 1.104,0.219 10 false Stop Light Switch 1.875,4.167 2.719,4.427 0.844,0.26 10 false Pedal Height 0.313,3.542 1.083,3.729 0.771,0.188 10 false Dash Panel

Measure the shortest distance between the brake pedal surface and dash panel.

Standard pedal height from dash panel:

179.9 to 189.9 mm (7.08 to 7.48 in.)


NOTICE:

Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.


If the pedal height is incorrect, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket and dash panel.

Even if there is damage, there is no problem if the reserve distance is within the standard value. If necessary, replace them.



Hide 84340 2.CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

HINT:

If the pedal height is incorrect, check and adjust the stop light switch clearance.


a.

Disconnect the stop light switch connector.


b.

Turn the stop light switch counterclockwise and remove it.


c.
U152162E02
0.448,1.802 1.396,2 0.948,0.198 10 false 1.5 to 2.5 mm 1.24,0.083 2.417,0.333 1.177,0.25 10 false Stop Light Switch

Insert the stop light switch until the body hits the cushion.

NOTICE:

When inserting the stop light switch, support the pedal from behind so that the pedal is not pushed in.



d.

Make a quarter turn clockwise to install the stop light switch.

NOTICE:

The turning torque for installing the stop light switch should be 1.5 N*m (15 kgf*cm, 13 in.*lbf) or less.


HINT:

Due to the inverse screw structure, if the stop light switch is turned clockwise, the stop light switch moves in the direction to be pulled out.



e.

Connect the stop light switch connector.


f.

Check the protrusion of the rod.

Standard protrusion of the rod:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)



Hide 47101 3.CHECK PEDAL FREE PLAY

a.
C208541E01
2.619,3.635 3.243,3.971 0.623,0.336 10 Pedal Free Play

Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.


b.

Push in the brake pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

Standard pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)



Hide 47101 4.CHECK PEDAL RESERVE DISTANCE

a.

Release the parking brake pedal.


b.
R000934E38
1.927,1.51 2.865,1.865 0.938,0.354 10 false Pedal Reserve Distance

With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

Standard pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):

More than 104 mm (4.09 in.)


If incorrect, troubleshoot the brake system (see page Brake>BRAKE>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).