Home › Brake › BRAKE › REAR BRAKE
RM27M0U _54 Brake _049123 BRAKE _0234119 REAR BRAKE A

BRAKE  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C211015E02
2.094,1.031 1.031,1.375 false 2.115,1.083 1.031,1.375 false 0.292,1.292 1.01,1.469 0.719,0.177 10 false Matchmark

Align the matchmarks and install the rear disc.


Hide 46520B 2.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 47722A 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

a.
C211010E01
0.729,4.164 2.735,4.323 2.007,0.159 10 Lithium soap base glycol grease

Apply a light coat of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake mounting cylinder, and the entire inner circumference of both ends.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.



b.
U152446

Install the rear disc brake bush dust boot to the rear disc brake cylinder mounting.

NOTICE:

Install the boot securely into the grooves of the rear disc brake cylinder mounting.



c.

Install the rear disc brake cylinder mounting with the 2 new bolts.

Torque:
167 N*m (1703 kgf*cm, 123 ft.*lbf)


Hide 4.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

NOTICE:
·

The pad support plates can be reused if they are securely attached to the cylinder mounting. Therefore, do not remove the pad support plates from the cylinder mounting.

·

If a pad support plate is removed, replace it with a new one that is supplied with double-sided tape already attached.

·

Make sure to clean the cylinder mounting contact surface before attaching the pad support plates.



a.

Clean the cylinder mounting surface where the pad support plates will be attached.


b.

Remove the peeling paper from the double-sided tape, and install 4 new pad support plates to the cylinder mounting.


Hide 5.INSTALL PAD WEAR INDICATOR PLATE

a.

Install the pad wear indicator plate to the inner disc brake pad.


Hide 04946 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

a.

Install the anti-squeal shims to the each brake pads.

NOTICE:

There should be no oil or grease on the friction surfaces of the brake pads and rear disc.



Hide 04466 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 disc brake pads to the disc brake cylinder mounting.

NOTICE:
·

When installing the pads, make sure that the disc brake pad support plates are securely attached to the cylinder mounting. The pad support plates are attached to the cylinder mounting with double-sided tape.

·

If a pad support plate is not securely attached to the cylinder mounting, replace it with a new one.




Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C211012E01
0.712,1.663 2.736,1.830 2.024,0.167 10 Lithium soap base glycol grease

Apply a light coat of lithium soap base glycol grease to the sliding part and seal surface of the 2 slide pins.


b.
C211017

Install the 2 slide pins.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


Hide 47319F 9.CONNECT REAR FLEXIBLE HOSE LH

a.
C211018

Install a new gasket and connect the flexible hose with the new union bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely in the lock hole in the cylinder.



Hide 10.BLEED BRAKE LINE

Hide 42603 11.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)