Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LOCK SYSTEM
RM27M0U _52 Drivetrain _049125 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0234132 SHIFT LOCK SYSTEM G

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LOCK SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK SHIFT LOCK OPERATION

a.

Move the shift lever to P.


b.

Turn the ignition switch off.


c.

Check that the shift lever cannot be moved to any position other than P.


d.

Turn the ignition switch to ON, depress the brake pedal and check that the shift lever can be moved to other positions.


Hide 33563 2.CHECK SHIFT LOCK RELEASE BUTTON OPERATION

a.

When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P.

If the operation cannot be performed as specified, check the shift lever assembly.


Hide 3.CHECK KEY INTERLOCK OPERATION

a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to any position other than P.


c.

Check that the ignition switch cannot be turned off.


d.

Move the shift lever to P, turn the ignition switch off and check that the key can be removed.

If the results are not as specified, inspect the shift lock control ECU.


Hide 85933 4.CHECK SHIFT LOCK CONTROL ECU (for Column Shift Type)

a.
C290568E03
1.917,1.302 1.635,0.594 1.635,0.594 1.49,0.594 false 1.448,3.781 1.188,3.24 1.188,3.24 1.052,3.24 true 1.99,3.771 2.25,3.229 2.25,3.229 2.375,3.229 true 2.146,4.354 2,4.052 true 1.313,4.354 1.458,4.063 true 1.771,4.063 1.771,4.375 true 2.24,4.021 2.583,4.021 true 1.313,0.51 1.469,0.688 0.156,0.177 10 false *1 0.708,2.792 0.865,2.969 0.156,0.177 10 false *a 0.885,3.156 1.052,3.333 0.167,0.177 10 false IG 2.427,3.135 2.74,3.313 0.313,0.177 10 false ACC 1.083,4.375 1.375,4.552 0.292,0.177 10 false STP 1.719,4.385 1.875,4.563 0.156,0.177 10 false E 2.052,4.385 2.417,4.563 0.365,0.177 10 false KLS+ 2.635,3.927 3,4.104 0.365,0.177 10 false SLS+

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
8 (KLS+) - 10 (E) Ignition switch ACC and shift lever in P Below 1 V
8 (KLS+) - 10 (E) Ignition switch ACC and shift lever not in P 7.5 to 11 V
8 (KLS+) - 10 (E) Ignition switch ACC and shift lever not in P (after approx. 1 second) 6 to 9 V
3 (ACC) - 10 (E) Ignition switch ON 10 to 14 V
3 (ACC) - 10 (E) Ignition switch ACC 10 to 14 V
3 (ACC) - 10 (E) Ignition switch off Below 1 V
13 (STP) - 10 (E) Brake pedal depressed 10 to 14 V
13 (STP) - 10 (E) Brake pedal released Below 1 V
4 (IG) - 10 (E) Ignition switch ON 10 to 14 V
4 (IG) - 10 (E) Ignition switch off Below 1 V
6 (SLS+) - 10 (E) Ignition switch ON and brake pedal depressed 10 to 14 V
6 (SLS+) - 10 (E) Ignition switch ON and brake pedal released Below 1 V


Text in Illustration
*1 Shift Lock Control ECU
*a Component with harness connected
(Shift Lock Control ECU)

If the result is not as specified, replace the shift lock control ECU.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Do not disconnect the shift lock control ECU connector.


Standard Resistance:
Tester Connection Condition Specified Condition
10 (E) - Body ground Always Below 1 Ω


If the result is not as specified, replace the shift lock control ECU.


Hide 85903 5.CHECK SHIFT LOCK CONTROL ECU (for Floor Shift Type)

C292570E03
2.229,1.49 2.469,0.813 2.469,0.813 2.563,0.813 true 1.365,1.75 1.01,0.74 1.01,0.74 0.917,0.74 true 2.938,2.615 2.229,1.74 true 1.5,2.604 1.813,1.729 true 2.083,1.75 2.083,2.625 true 1.833,1.5 2.198,0.49 2.198,0.49 2.281,0.49 true 0.25,0.104 0.406,0.281 0.156,0.177 10 false *a 2.313,0.396 2.604,0.573 0.292,0.177 10 false STP 2.594,0.719 2.75,0.896 0.156,0.177 10 false E 1.396,2.615 1.563,2.792 0.167,0.177 10 false IG 1.906,2.635 2.219,2.813 0.313,0.177 10 false ACC 2.802,2.625 3.167,2.802 0.365,0.177 10 false KLS+ 0.531,0.646 0.896,0.823 0.365,0.177 10 false SLS+

a.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
5 (KLS+) - 1 (E) Ignition switch ACC and shift lever in P Below 1 V
5 (KLS+) - 1 (E) Ignition switch ACC and shift lever not in P 7.5 to 11 V
5 (KLS+) - 1 (E) Ignition switch ACC and shift lever not in P (after approx. 1 second) 6 to 9 V
6 (ACC) - 1 (E) Ignition switch ON 10 to 14 V
6 (ACC) - 1 (E) Ignition switch ACC 10 to 14 V
6 (ACC) - 1 (E) Ignition switch off Below 1 V
4 (STP) - 1 (E) Brake pedal depressed 10 to 14 V
4 (STP) - 1 (E) Brake pedal released Below 1 V
8 (IG) - 1 (E) Ignition switch ON 10 to 14 V
8 (IG) - 1 (E) Ignition switch off Below 1 V
SLS+ - 1 (E) Ignition switch ON and brake pedal depressed 10 to 14 V
SLS+ - 1 (E) Ignition switch ON and brake pedal released Below 1 V


Text in Illustration
*a Component with harness connected
(Shift Lock Control ECU)

If the result is not as specified, replace the shift lock control ECU.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Do not disconnect the shift lock control ECU connector.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


If the result is not as specified, replace the shift lock control ECU.


Hide 85431 6.CHECK SHIFT LOCK SOLENOID (for Column Shift Type)

a.

Disconnect the transmission control switch connector.


b.
C159631E05
2.188,1.833 2.052,0.917 2.052,0.917 1.823,0.917 true 2.188,2.906 2.188,2.177 true 1.396,0.813 1.771,0.99 0.375,0.177 10 false SLS+ 2.135,2.917 2.26,3.094 0.125,0.177 10 false E 0.146,0.156 0.344,0.427 0.198,0.271 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 8 (E) Always 24 to 26 Ω


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)

If the result is not as specified, replace the shift lock solenoid.


Hide 85431 7.CHECK SHIFT LOCK SOLENOID (for Floor Shift Type)

a.

Disconnect the shift lock solenoid connector from the shift lock control ECU.


b.
C150404E14
1.198,2.01 0.948,1.156 true 1.531,2.031 1.781,1.177 true 1.167,2.073 1.271,2.26 0.104,0.188 10 false 1 1.51,2.073 1.615,2.26 0.104,0.188 10 false 2 1.854,2.073 1.958,2.26 0.104,0.188 10 false 3 2.188,2.063 2.292,2.25 0.104,0.188 10 false 4 1.688,0.979 2.198,1.271 0.51,0.292 10 false SLS- 0.802,0.979 1.271,1.156 0.469,0.177 10 false SLS+ 0.156,0.125 0.625,0.302 0.469,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SLS+) - 3 (SLS-) Always 101 to 123 Ω


Text in Illustration
*a Component without harness connected
(Shift Lock Solenoid)

If the result is not as specified, replace the floor shift assembly.


Hide 85432 8.CHECK KEY INTERLOCK SOLENOID

a.

Disconnect the solenoid connector.


b.
C159632E04
2.849,1.819 3.283,2.031 0.434,0.211 10 SOL+ 0.323,1.819 0.676,1.961 0.353,0.142 10 SOL- 1.492,2.262 0.96,1.894 0.96,1.894 0.777,1.894 false 1.969,2.283 2.585,1.912 2.585,1.912 2.768,1.912 false 0.14,0.115 0.351,0.326 0.211,0.211 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SOL+) - 2 (SOL-) 20°C (68°F) 14.4 Ω


Text in Illustration
*a Component without harness connected
(Key Interlock Solenoid)

If the result is not as specified, replace the solenoid.


c.

Connect the positive (+) battery lead to terminal 1 (SOL+) and the negative (-) battery lead to terminal 2 (SOL-).

Check that the operating noise of the solenoid can be heard.

If the result is not as specified, replace the solenoid.