Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM27M0U _52 Drivetrain _049125 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0234141 AUTOMATIC TRANSMISSION UNIT A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

C159655

a.

Remove the nut, spring washer and control shaft lever.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C159656

a.

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 89413B 3.REMOVE SPEED SENSOR

C159658

a.

Remove the 2 bolts and 2 speed sensors.


b.

Remove the 2 O-rings from sensors.


Hide 33490F 4.REMOVE TRANSMISSION OIL COOLER ASSEMBLY

C161366

a.

w/ Trailer Towing System:

i.

Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.


ii.

Separate the transmission oil cooler from the transmission oil thermostat.


iii.

Remove the 4 O-rings.



b.
C161367

w/o Trailer Towing System:

i.

Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.


ii.

Separate the transmission oil cooler from the transmission oil cooler spacer.


iii.

Remove the 4 O-rings.



Hide 35122 5.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C159659

a.

Remove the 2 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 35111 6.REMOVE AUTOMATIC TRANSMISSION HOUSING

C159660

a.

Remove the 14 bolts.


b.

Remove the transmission housing.


Hide 35015G 7.REMOVE TRANSFER ADAPTER REAR

C162765

a.

Remove the 10 bolts.


b.

Remove the rear adaptor transfer.

HINT:

Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear adaptor transfer.



Hide 35015C 8.REMOVE TRANSMISSION CASE ADAPTER OIL SEAL

C162766

a.

Using a screwdriver, pry out the oil seal.

NOTICE:

Be careful not to damage the rear adaptor transfer. Wrap the tip of the screwdriver with tape.



Hide 35015E 9.REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING

C162767E01
2.439,0.287 2.756,0.466 0.317,0.178 10 SST 2.413,0.413 1.79,0.919 false

a.

Using a screwdriver, remove the snap ring.


b.

Using SST and a press, press out the bearing.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35104 10.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

C161613

a.

Install the transmission case on the overhaul attachment.


Hide 35106 11.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

U152357

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.


a.

Remove the drain plug, 12 bolts, oil pan and gasket.


Hide 35106 12.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35330 13.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C161111

a.

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body.


c.

Remove the O-ring from the oil strainer.


Hide 82125J 14.REMOVE TRANSMISSION WIRE

U152298

a.

Remove the 2 bolts and 2 temperature sensor clamps.


b.

Disconnect the 2 ATF temperature sensors.


c.

Disconnect the 9 connectors from the solenoid valves.


d.
C161614

Remove the 2 bolts and pull out the No. 1 and No. 2 transmission wires.


e.

Pull the transmission wires out of the transmission case.


f.
C161615

Remove the 2 O-rings from the transmission wires.


Hide 35410 15.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.

Remove the bolt, detent spring cover and detent spring.


b.
U152342

Remove the 19 bolts.


c.

Remove the valve body assembly.


Hide 35145C 16.REMOVE TRANSMISSION CASE GASKET

C161616

a.

Remove the 3 gaskets.


Hide 35159 17.REMOVE BRAKE DRUM GASKET

C161617

a.

Remove the 3 gaskets.


Hide 35251 18.REMOVE CHECK BALL BODY

C161618E03
1.844,0.573 1.521,0.573 true 1.844,1.167 1.427,1.167 true 1.875,0.479 2.979,0.708 1.104,0.229 10 true Check Ball Body 1.896,1.073 2.375,1.281 0.479,0.208 10 false Spring

a.

Remove the check ball body and spring.


Hide 35425A 19.REMOVE C-2 ACCUMULATOR PISTON

C161619

a.

While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 35427K 20.REMOVE B-3 ACCUMULATOR PISTON

C161619

a.

While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 35426D 21.REMOVE C-3 ACCUMULATOR PISTON

C161620

a.

While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.


Hide 35424F 22.REMOVE B-1 ACCUMULATOR VALVE

C161621

a.

Remove the B-1 accumulator valve and 2 springs.


Hide 35595 23.REMOVE PARKING LOCK PAWL BRACKET

C161622

a.

Remove the 3 bolts and bracket.


Hide 35501 24.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

U152320

a.

Disconnect the parking lock rod from the manual valve lever.


Hide 35557 25.REMOVE PARKING LOCK PAWL

U152321

a.

Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 35505 26.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918E01
2.99,0 3.414,0.103 0.424,0.103

a.

Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.


b.
C161626

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly tap out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the transmission case, and remove the manual valve lever.


Hide 35506F 27.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C161628

a.

Using a screwdriver, pry out the 2 oil seals.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape before use.



Hide 28.REMOVE OIL PUMP ASSEMBLY

C161629

a.

Remove the 10 bolts.


b.
C161630E01
2.68,0.691 2.999,0.879 0.319,0.189 10 SST 2.645,0.827 2.182,0.949 false

Using SST, pull out the oil pump.

SST
09950-40011  (09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031)


c.
C161631

Remove the O-ring and 2 thrust bearing races from the oil pump.


Hide 29.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161632

a.

Remove the clutch drum and input shaft drum assembly from the transmission case.


b.
C161633

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 35780B 31.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

C161634

a.

Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 32.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161636E03
1.052,1.25 0.792,1.104 false 2.313,1.073 2.51,1.073 true 2.552,0.99 3.198,1.208 0.646,0.219 10 false Oil Pump 0.208,0.969 0.844,1.49 0.635,0.521 10 false Torque Converter Clutch

a.

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.


Hide 35049 33.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

C161637

a.

Using a screwdriver, remove the snap ring.


b.
C161638

Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly with the rear clutch disc set from the clutch drum.


Hide 35677C 34.REMOVE REAR CLUTCH DISC SET

C161640

a.

Remove the selective reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


b.
C162148

Remove the reverse clutch flange from the clutch drum.


Hide 35061 37.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C161641

a.

Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.


Hide 35064 39.REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

C161642

a.

Remove the 2 thrust needle roller bearings, coast clutch hub with the No. 4 1-way clutch and thrust bearing race from the clutch drum.


Hide 35790H 41.REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY

C161643

a.

Separate the No. 4 1-way clutch from the coast clutch hub.


b.

Remove the No. 2 clutch hub thrust washer from the coast clutch hub.


Hide 35633B 42.REMOVE FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC SET

C161644

a.

Using a screwdriver, remove the hole snap ring.


b.
C161645

Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.


Hide 35633B 43.INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

Hide 35685 44.REMOVE COAST CLUTCH DISC SET

C161646

a.

Using a screwdriver, remove the hole snap ring.


b.
C161647

Remove the flange, 4 discs and 4 plates from the input shaft.


Hide 35701 46.REMOVE INPUT SHAFT SUB-ASSEMBLY

C161648

a.

Remove the input shaft from the clutch drum.


Hide 35712A 47.REMOVE INPUT SHAFT OIL SEAL RING

C161649

a.

Remove the 4 oil seal rings from the input shaft.


Hide 35621Y 48.REMOVE COAST CLUTCH PISTON

C161650E01
2.76,0.626 3.084,0.812 0.324,0.186 10 SST 2.137,0.648 2.715,0.708 2.715,0.708 1.633,0.943 false

a.

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C161651

Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.


d.
C161652

Remove the O-ring from the No. 1 clutch balancer.


e.
C161653

Hold the coast clutch piston by hand and apply compressed air to the input shaft to remove the coast clutch piston.


Hide 35603A 49.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35602A 50.REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

C161654

a.

Hold the forward clutch piston by hand and apply compressed air to the input shaft to remove the forward clutch piston.


b.
C162744

Remove the O-ring from the input shaft.


Hide 35603A 51.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35667A 52.REMOVE DIRECT CLUTCH DISC SET

C159654

a.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.


b.
C161655

Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.


Hide 35668 54.REMOVE NO. 3 CLUTCH BALANCER

C161656E01
2.693,0.685 3.029,0.858 0.336,0.173 10 SST 2.127,0.674 2.641,0.815 2.641,0.815 1.988,1.641 false

a.

Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

SST
09380-60010  (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the No. 3 clutch balancer.


d.
C161657

Remove the reverse clutch return spring and O-ring from the reverse clutch piston sub-assembly.


Hide 35047 55.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35048 56.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

C161700

a.

Remove the reverse clutch piston from the clutch drum.


b.
C161702

Remove the O-ring from the reverse clutch piston.


c.
C161703

Remove the O-ring from the clutch drum.


Hide 35606A 57.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

C161704E01
0.111,0.511 0.425,0.699 0.314,0.188 10 SST 1.952,1.079 0.504,0.636 0.504,0.636 1.118,0.73 false

a.

Place SST on the direct clutch piston, and compress the return spring with a press.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Place the oil pump onto the torque converter clutch, and then place the clutch drum onto the oil pump.


d.
U152323E01
2.451,1.989 3.037,2.190 0.586,0.201 10 Oil Hole 3.18,0.943 3.18,2.099 3.18,2.099 3.101,2.099 false

Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston with the No. 2 clutch balancer and direct clutch return spring sub-assembly.


e.
C161706

Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.


f.
C161812

Remove the 2 O-rings from the direct clutch piston.


Hide 35604 58.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35679C 59.REMOVE NO. 3 BRAKE SNAP RING

C161635

a.

Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.


Hide 35066 60.REMOVE NO. 3 BRAKE DISC SET

C161707

a.

Remove the 2 flanges, 4 discs and 3 plates from the transmission case.


Hide 35624J 62.REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

C161708E02
2.781,0.385 2.365,0.25 true 2.823,0.302 3.135,0.5 0.313,0.198 10 false SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 35664 63.REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161709

a.

Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.


Hide 35624 64.REMOVE NO. 3 BRAKE PISTON

C162151E01
0.361,0.071 0.722,0.257 0.361,0.187 10 SST 0.713,0.202 1.031,0.367 false

a.

Using SST and a press, compress the return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

SST
09380-60010  (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)


b.
C161712

Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.


c.
C161713

Remove the 2 O-rings from the No. 3 brake piston.


Hide 35046 65.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35790 66.REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161710

a.

Remove the 1-way clutch with 1-way clutch inner race from the transmission case.


Hide 35707C 68.REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161711

a.

Separate the 1-way clutch inner race from the 1-way clutch and remove the No. 1 planetary carrier thrust washer.


Hide 35720 69.REMOVE FRONT PLANETARY GEAR ASSEMBLY

C161714

a.

Remove the front planetary gear and thrust needle roller bearing from the transmission case.


b.
C161715

Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear.


Hide 35743 71.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

C161716

a.

Remove the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear from the transmission case.


b.

Remove the thrust needle roller bearing and thrust bearing race.


Hide 35743 72.REMOVE FRONT PLANETARY RING GEAR

C161717

a.

Using a screwdriver, remove the snap ring.


b.
C161718

Remove the front planetary ring gear from the center planetary ring gear.


Hide 35763 73.REMOVE CENTER PLANETARY RING GEAR

C161719

a.

Using a screwdriver, remove the snap ring.


b.
C161720

Remove the center planetary ring gear from the front planetary ring gear flange.


Hide 35681A 74.REMOVE NO. 1 BRAKE DISC SET

C161721

a.

Remove the flange, 4 discs and 4 plates from the transmission case.


Hide 35698 76.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

C162153E01
3.022,1.461 3.345,1.661 0.323,0.200 10 SST 2.987,1.511 2.699,1.434 false

a.

Place SST on the No. 1 brake piston return spring, and compress the return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.


c.
C161723

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


Hide 35608J 77.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621V 78.REMOVE NO. 1 BRAKE PISTON

C161724

a.

Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162732

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35682A 79.REMOVE NO. 2 BRAKE DISC SET

C162561E02
2.99,1.677 2.656,1.438 true 3.021,1.635 3.333,1.865 0.313,0.229 10 true SST

a.

Place SST on the No. 2 brake flange, and compress the return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.


c.
C161726

Remove the 2 flanges, 4 discs, 3 plates and brake piston return spring from the transmission case.


Hide 35045 81.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35750 82.REMOVE CENTER PLANETARY GEAR ASSEMBLY

C161727

a.

Remove the center planetary gear and planetary sun gear from the transmission case.


Hide 35699 84.REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

C161728

a.

Remove the No. 2 brake cylinder with the No. 2 brake piston from the transmission case.


Hide 35622G 85.REMOVE NO. 2 BRAKE PISTON

C162149

a.

Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162730

Remove the 2 O-rings from the No. 2 brake piston.


Hide 35713 86.REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

C161730E02
0.51,1.354 0.51,1.01 true 0.365,1.375 0.667,1.563 0.302,0.188 10 true SST

a.

Using SST, remove the snap ring from the transmission case.

SST
09350-30020  (09350-07060)


b.
C161731

Remove the intermediate shaft with No. 3 1-way clutch, rear planetary ring gear flange and rear planetary ring gear from the transmission case.


Hide 35770C 88.REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

C161732

a.

Remove the No. 3 1-way clutch and 1-way clutch inner race from the intermediate shaft.


Hide 35761 89.REMOVE REAR PLANETARY RING GEAR

C161733

a.

Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.


b.
C161734

Using a screwdriver, remove the snap ring.


c.

Remove the rear planetary ring gear flange from the rear planetary ring gear.


Hide 35684 91.REMOVE NO. 4 BRAKE DISC SET

C161736

a.

Remove the 2 flanges, 7 discs and 6 plates from the transmission case.


Hide 35639B 93.REMOVE BRAKE PLATE STOPPER SPRING

C161735

NOTICE:

When removing the stopper spring, do not apply excessive force and do not deform it.


Hide 35760 94.REMOVE REAR PLANETARY GEAR ASSEMBLY

C162771

a.

Remove the rear planetary gear from the transmission case.


b.
C162772

Remove the 2 thrust needle roller bearings from the rear planetary gear.


c.
C161739

Remove the thrust bearing race from the transmission case.


Hide 35623H 96.REMOVE 1ST AND REVERSE BRAKE PISTON

C162152E01
0.206,0.522 0.557,0.737 0.350,0.215 10 SST 0.913,0.709 0.601,0.626 false

a.

Place SST on the spring retainer and compress the brake return spring.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


c.
C161740

Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



d.
C161741

Remove the 3 O-rings from the 1st and reverse brake piston.


Hide 35068 97.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY