Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049125 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0234142 AUTOMATIC TRANSMISSION SYSTEM D

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


a.

Measure the line pressure.

CAUTION:

The line pressure test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

This check must be conducted after checking and adjusting the engine.

·

Perform the test with the A/C OFF.

·

When conducting stall test, do not continue for more than 5 seconds.

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



i.

Warm up the ATF (Automatic Transmission Fluid).


ii.

Turn the ignition switch off.


iii.

Lift the vehicle up.


iv.
C161166E01
2.116,0.715 2.458,0.905 0.342,0.190 10 SST 2.446,0.517 2.287,0.694 false 0.288,3.989 0.953,4.174 0.666,0.185 10 Test Plug 1.578,3.742 1.107,4.074 1.107,4.074 1.045,4.074 false 0.123,1.731 0.464,1.922 0.342,0.190 10 SST 0.384,1.406 0.294,1.711 false

Remove the test plug on the transmission case center right side and connect SST.

SST
09993-19015  (09993-00040, 09993-00010)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock the 4 wheels.


vii.

Start the engine and check the idling speed.


viii.

Keep your left foot pressed firmly on the brake pedal and move the shift lever to D.


ix.

Fully depress the accelerator pedal with your right foot. Quickly read the highest line pressure when the engine speed reaches the stall speed.


x.

In the same manner, perform the test with the shift lever in R.

Specified Line Pressure (3UR-FE)
Condition D Position R Position
Stall speed 1170 to 1340 kPa
(11.9 to 13.7 kgf/cm2, 170 to 194 psi)
1540 to 1850 kPa
(15.7 to 18.9 kgf/cm2, 223 to 268 psi)

Specified Line Pressure (3UR-FBE)
Condition D Position R Position
Stall speed 1020 to 1180 kPa
(10.4 to 12.0 kgf/cm2, 148 to 171 psi)
1500 to 1720 kPa
(15.3 to 17.5 kgf/cm2, 218 to 249 psi)

Evaluation
Problem Possible Cause
Measured values at both positions are higher than specified pressure
·

Shift solenoid valve SLT defective

·

Regulator valve defective


Measured values at both positions are lower than specified pressure
·

Shift solenoid valve SLT defective

·

Regulator valve defective

·

Oil pump defective


Pressure is low in D position only
·

D position circuit fluid leak

·

Clutch No. 1 (C1) defective


Pressure is low in R position only
·

R position circuit fluid leak

·

Clutch No. 3 (C3) defective

·

Brake No. 4 (B4) defective