Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION FLUID
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234176 AUTOMATIC TRANSMISSION FLUID A

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSMISSION FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.

Remove the drain plug and gasket, and drain the ATF. [*2]


c.

Temporarily install the gasket and drain plug. [*3]

HINT:

Reuse the old gasket. A new gasket will be installed in step [*15].



d.
C209343E03
2.24,3.729 1.521,4.26 1.521,4.26 1.427,4.26 false 1.198,1.406 1.438,0.125 1.438,0.125 1.542,0.125 false 2.396,2.25 2.333,2.563 2.333,2.563 2.417,2.563 false 2.479,2.479 3.156,2.677 0.677,0.198 10 false Refill Plug 1.573,0.052 2.24,0.26 0.667,0.208 10 false Refill Hole 0.552,4.167 1.521,4.365 0.969,0.198 10 false Overflow Plug

Remove the refill plug and overflow plug. [*4]


e.
C351951E01
2.51,1.115 1.802,0.802 true 0.823,1.188 1.031,0.781 true 2.188,1.146 3.167,1.344 0.979,0.198 10 false Overflow Tube 0.188,1.229 1.552,1.417 1.365,0.188 10 false Specified Fluid Level

Add fluid to the refill hole until it flows out of the overflow plug hole. [*5]

NOTICE:

Use Toyota Genuine ATF WS.



f.

Wait until the fluid flow slows and only drops come out. [*6]


g.

Temporarily install the gasket and overflow plug. [*7]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



h.

Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8]

HINT:

Specified amount of fluid is 2.1 liters (2.2 US qts, 1.8 Imp. qts).



i.

Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



j.

Lower the vehicle. [*10]


k.

Start the engine. [*11]

NOTICE:

Make sure that the A/C switch is off.



l.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then return the shift lever to P. [*12]


m.

Allow the engine to idle for 30 seconds to warm it up. [*13]


n.

Turn the ignition switch off. [*14]


o.

Repeat steps [*1] to [*14].


p.

Repeat steps [*1] to [*2].


q.

Install a new gasket and the drain plug[*15].

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


r.

Repeat steps [*4] to [*10].



t.

Lower the vehicle.


u.

Operation complete.