Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234192 AUTOMATIC TRANSMISSION SYSTEM C

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0761  Shift Solenoid "C" Performance (Shift Solenoid Valve S3)  


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body and automatic transmission (clutch, brake, gear, etc.).

DTC Code DTC Detection Condition Trouble Area
P0761

S3 stuck ON malfunction*1:

When the ECM directs the transmission to switch to 5th or 6th gear, the engine overruns (clutch slips).

The ECM determines there is a malfunction when either of the following conditions is met (2-trip detection logic):


(a) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
(b) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips).
·

Shift solenoid valve S3 remains closed

·

Shift solenoid valve SLT remains closed

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)


P0761

S3 stuck OFF malfunction*2:

Shifting to 1st, 2nd and 3rd gears is impossible.

The ECM determines there is a malfunction when the following conditions are both met (2-trip detection logic):


(a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 6th.
·

Shift solenoid valve S3 remains open

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)



HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under S3 stuck ON malfunction 1st 2nd 3rd 3rd N* N*
*2: Actual gear position under S3 stuck OFF malfunction 3rd 4th 4th 4th 5th 6th

N*: Neutral

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under fail-safe mode during S3 stuck ON malfunction 1st 2nd 3rd 3rd 3rd 3rd
*2: Actual gear position under fail-safe mode during S3 stuck OFF malfunction 3rd 4th 4th 4th 5th 6th



MONITOR DESCRIPTION

This DTC indicates a "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S3.

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Related DTCs P0761: Shift solenoid valve S3/Functional check
Required sensors/Components Shift solenoid valve S3
Frequency of operation Continuous
Duration OFF malfunction (A), (B) and ON malfunction (A)
0.4 seconds
ON malfunction (B)
3 seconds
ON malfunction (C)
1 second
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0717 (Turbine speed sensor circuit)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit)
P0500 (Vehicle speed sensor circuit)
ETCS (Electric Throttle Control System) Not system down
Transmission position "D"
Duration time from shifting "N" to "D" 4 seconds or more
ECT 40°C (104°F) or higher
Spark advance from max. retard timing by KCS control 0° crankshaft angle or more
Engine Starting

OFF Malfunction (A)
ECM selected gear 2nd
Vehicle speed 2 km/h (1.2 mph) or more
Output speed 2nd → 1st down-shift point or more
Throttle valve opening angle 6.6% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.30 to 7.50
or
1.91 to 2.35
or
1.28 to 1.53
or
0.93 to 1.07
or
0.65 to 0.79
or
0.51 to 0.65

OFF Malfunction (B)
ECM selected gear 6th
Vehicle speed 2 km/h (1.2 mph) or more
Throttle valve opening angle 6.6% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.30 to 7.50
or
1.91 to 2.35
or
1.28 to 1.53
or
0.93 to 1.07
or
0.65 to 0.79
or
0.51 to 0.65

ON Malfunction (A)
ECM selected gear 4th
Vehicle speed 2 km/h (1.2 mph) or more
Throttle valve opening angle 6.6% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.30 to 7.50
or
1.91 to 2.35
or
1.28 to 1.53
or
0.93 to 1.07
or
0.65 to 0.79
or
0.51 to 0.65

ON Malfunction (B)
Current ECM selected gear 5th
Last ECM selected gear 4th
Vehicle speed (During transition from 4th to 5th gear) Less than 100 km/h (62.2 mph)

ON Malfunction (C)
ECM selected gear 5th
Engine speed - Turbine speed (NE - NT) (After transition to 5th gear) 150 rpm or less
Vehicle speed (After transition to 5th gear) Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]

Both of the following conditions are met: OFF malfunctions (A) and (B)


OFF Malfunction (A)
Turbine speed / Output speed (NT / NO) 0.93 or more, and 1.07 or less
(This means actual gear is 4th)

OFF Malfunction (B)
Turbine speed / Output speed (NT / NO) 0.51 or more, and 0.65 or less
(This means actual gear is 6th)

[ON malfunction]

One of the following conditions is met: ON malfunctions (A), (B) or (C)


ON Malfunction (A)
Turbine speed / Output speed (NT / NO) 1.28 or more, and 1.53 or less
(This means actual gear is 3rd)

ON Malfunction (B)
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more

ON Malfunction (C)
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


ACTIVE TEST


HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the Techstream.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the Techstream.

·

The shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S3 ON ON ON OFF OFF OFF





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0761)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the Techstream.

Result
Result Proceed to
Only P0761 is output A
P0761 and other DTCs are output B

HINT:

If any other codes besides P0761 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

OK

3.INSPECT SHIFT SOLENOID VALVE S3

NG

3.INSPECT SHIFT SOLENOID VALVE S3
a.
C209925E03
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 2.413,0.126 2.664,0.328 0.251,0.202 10 (+) 1.695,0.126 1.900,0.328 0.206,0.202 10 (-)

Remove shift solenoid valve S3.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S3 connector

·

Battery negative (-) → Shift solenoid valve S3 body


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve S3)


OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY