Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234192 AUTOMATIC TRANSMISSION SYSTEM C

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0781  1-2 Shift (1-2 Shift Valve)  


DESCRIPTION

The 1-2 shift valve performs shifting to 1st gear and other gears. When shifting to 2nd and 4th gears is impossible, or when the ECM directs the transmission to switch to 5th or 6th gear and the engine overruns (clutch slips), this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
P0781

Conditions (a) and (b), or (a) and (c) are met (2-trip detection logic):


(a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st.
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
(c) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips).
·

Valve body is blocked or stuck (1-2 shift valve)

·

Shift solenoid valve SLT remains open or closed

·

Automatic transmission (clutch, brake, gear, etc.)



HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 1st 3rd 3rd N* N*

N*: Neutral

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.


Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
Actual gear position under fail-safe mode 1st* 1st* 3rd 3rd 3rd 3rd

1st*: Under engine braking, downshifting to 1st or 2nd gear is prohibited.



MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction the spring compresses.

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF and switching oil pressure to the valves in the valve body.

The ECM calculates the "actual" transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0781: Valve body / Functional check
Required sensors/Components Valve body, Automatic transmission assembly
Frequency of operation Continuous
Duration Condition (A) and (B)
0.4 seconds
Condition (C)
3 seconds
Condition (D)
1 second
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0717 (Turbine speed sensor circuit)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit)
P0500 (Vehicle speed sensor circuit)
ETCS (Electric Throttle Control System) Not system down
Transmission position "D"
Duration time from shifting "N" to "D" 4 seconds or more
ECT 40°C (104°F) or higher
Spark advance from max. retard timing by KCS control 0° crankshaft angle or more
Engine Starting

Condition (A)
ECM selected gear 2nd
Vehicle speed 2 km/h (1.2 mph) or more
Output speed 2nd → 1st down-shift point or more
Throttle valve opening angle 6.6% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.30 to 7.50
or
1.91 to 2.35
or
1.28 to 1.53
or
0.93 to 1.07
or
0.65 to 0.79
or
0.51 to 0.65

Condition (B)
ECM selected gear 4th
Vehicle speed 2 km/h (1.2 mph) or more
Throttle valve opening angle 6.6% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value 7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.30 to 7.50
or
1.91 to 2.35
or
1.28 to 1.53
or
0.93 to 1.07
or
0.65 to 0.79
or
0.51 to 0.65

Condition (C)
Current ECM selected gear 5th
Last ECM selected gear 4th
Vehicle speed (During transition from 4th to 5th gear) Less than 100 km/h (62.2 mph)

Condition (D)
ECM selected gear 5th
Engine speed -Turbine speed (NE - NT) (After transition to 5th gear) 150 rpm or less
Vehicle speed (After transition to 5th gear) Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: Condition (A), and Condition (B), (C) or (D)


Condition (A)
Turbine speed / Output speed (NT / NO) 3.30 or more, and 7.50 or less
(This means actual gear is 1st)

Condition (B)
Turbine speed / Output speed (NT / NO) 1.28 or more, and 1.53 or less
(This means actual gear is 3rd)

Condition (C)
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more

Condition (D)
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0781)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the Techstream.

Result
Result Proceed to
Only P0781 is output A
P0781 and other DTCs are output B

HINT:

If any other codes besides P0781 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)
HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the Techstream.


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the Techstream.

·

Gear positions in the event of a solenoid valve mechanical problem:

Tester gear shift command 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 1st 3rd 3rd N* N*

N*: Neutral

OK:

Gear position changes in accordance with the Techstream command.






OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

OK

4.CLEAR DTC AND PERFORM RUNNING TEST

NG