Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234192 AUTOMATIC TRANSMISSION SYSTEM D

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

When troubleshooting On-Board Diagnostic (OBD II) vehicles, the vehicle must be connected to the OBD II scan tool (complying with SAE J1987). Various data output from the vehicle's ECM can then be read.


b.
C140856

OBD II regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

·

The emission control system/components

·

The powertrain control components (which affect vehicle emissions)

·

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by SAE J2012 are recorded in the ECM memory.

When the malfunction does not reoccur, the MIL stays illuminated until the ignition switch is turned off, and the MIL turns off when the engine is started. However, the DTCs remain recorded in the ECM memory.


c.

To check DTCs, connect the Techstream to the Data Link Connector 3 (DLC3) of the vehicle. The Techstream displays DTCs, freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared with the Techstream (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).



NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2-trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1-trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions.



2-TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

Freeze frame data records the engine conditions (fuel system data, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


b.
C140837E08
0.375,1.74 3.052,1.969 2.677,0.229 10 Freeze frame data which can be read 0.698,0.656 1.281,0.906 0.583,0.25 10 0.5 sec. 1.344,0.656 1.938,0.896 0.594,0.24 10 0.5 sec. 1.969,0.667 2.625,0.885 0.656,0.219 10 0.5 sec. 1.865,0.052 2.917,0.292 1.052,0.24 10 DTC is stored

The Techstream records freeze frame data at 5 different times: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. These data can be used to reproduce the vehicle conditions around the time when the malfunction occurred. The data may be helpful in finding the cause of the malfunction, or determining if the DTC is being caused by a temporary malfunction or not.




CHECK MIL


a.

Check that the MIL illuminates when turning the ignition switch to ON.

If the MIL does not illuminate, there is a problem in the MIL circuit (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).


b.

When the engine is started, the MIL should turn off.