Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27M0U _55 Steering _049129 STEERING COLUMN _0234195 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM D

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch ON and check the freeze frame data by following the prompts on the Techstream screen.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tilt Position Current tilt position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Position Current telescopic position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Return Position Memorized tilt return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Return Position Memorized telescopic return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges) 7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Up Switch Input state of tilt up by manual switch / ON or OFF ON: Tilt up is activated by manual switch
OFF: Tilt up is not activated by manual switch
-
Tilt Up SW(CAN) Communication state of tilt up input by manual switch / ON or OFF ON: Tilt up is activated by manual switch
OFF: Tilt up is not activated by manual switch
-
Tilt Down Switch Input state of tilt down by manual switch / ON or OFF ON: Tilt down is activated by manual switch
OFF: Tilt down is not activated by manual switch
-
Tilt Down SW(CAN) Communication state of tilt down input by manual switch / ON or OFF ON: Tilt down is activated by manual switch
OFF: Tilt down is not activated by manual switch
-
Telesco Short Switch Input state of telescopic short by manual switch / ON or OFF ON: Telescopic short is activated by manual switch
OFF: Telescopic short is not activated by manual switch
-
Telesco Short SW(CAN) Communication state of telescopic short input by manual switch / ON or OFF ON: Telescopic short is activated by manual switch
OFF: Telescopic short is not activated by manual switch
-
Telesco Long Switch Input state of telescopic long by manual switch / ON or OFF ON: Telescopic long is activated by manual switch
OFF: Telescopic long is not activated by manual switch
-
Telesco Long SW(CAN) Communication state of telescopic long input by manual switch / ON or OFF ON: Telescopic long is activated by manual switch
OFF: Telescopic long is not activated by manual switch
-
T&T Manual SW Data Voltage data of manual switch / min.: 0.00 V, max.: 4.99 V Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
Power Source Voltage Voltage data of power supply / min.: 0.00 V, max.: 19.99 V Actual power supply voltage
11 to 14 V
-
Freeze Speed Info Vehicle speed data / min: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
IG Switch (CAN) Communication state of ignition switch / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
IG Switch Input state of ignition switch / ON or OFF ON: Input signal is normal
OFF: Input signal is interrupted
-
Key Switch(CAN) Communication state of unlock warning switch signal / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Key Switch Input state of unlock warning switch / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Key Code Confirm(CAN) Communication state of key code confirmation signal / ON or OFF ON: Communication is normal
OFF: Communication is interrupted
-
Receive from Meter Communication state of combination meter signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
Receive from Seat ECU Communication state of front power seat control ECU and switch LH signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
Receive from Combi Communication state of combination switch ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
J/B Communication state of main body ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
B/B Communication state of optional after parts ECU signal / OK or Interpt OK: Communication is normal
Interpt: Communication is interrupted
-
The Number of DTCs Number of diagnostic trouble codes / min.: 0, max.: 255 Actual number of diagnostic trouble codes -