Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)
RM27M0U _55 Steering _049129 STEERING COLUMN _0234197 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When using a vise, do not overtighten it.


PROCEDURE

Hide 89227 1.REMOVE MULTIPLEX TILT AND TELESCOPIC ECU

a.
C159704

Disconnect the 2 ECU connectors.


b.

Remove the 2 screws and ECU.


Hide 89783 2.REMOVE TRANSPONDER KEY AMPLIFIER

a.
C155153

Using a screwdriver, widen the claws attached to the upper bracket by approximately 1.0 mm (0.0394 in.).


b.

Pull out the transponder key amplifier with the claws open.

NOTICE:

Using excessive force may damage the case.



Hide 45271 3.REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY

a.

Secure the steering column in a vise.


b.

Using a center punch, mark the center of the 2 tapered-head bolts.


c.

Using a 3 to 4 mm (0.119 to 0.159 in.) drill, drill a hole in the 2 tapered-head bolts.


d.
C159754

Using a screw extractor, remove the 2 tapered-head bolts, and then remove the upper steering column with switch bracket and the steering lock bracket from the steering column.


Hide 69057A 4.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch lock cylinder to the ACC position.


b.
C352952E01
2.083,0.646 2.219,0.354 2.219,0.354 2.104,0.354 true 2.042,1.021 2.115,1.021 2.115,1.021 2.156,0.708 true 1.438,0.49 1.75,0.688 0.313,0.198 10 false *a 1.927,0.26 2.135,0.458 0.208,0.198 10 false *c 1.875,0.927 2.083,1.125 0.208,0.198 10 false *d 1.594,2.021 1.802,2.219 0.208,0.198 10 false *b 0.917,2.021 1.125,2.219 0.208,0.198 10 false *h 0.438,2.177 0.646,2.375 0.208,0.198 10 false *g 0.323,2.615 0.531,2.813 0.208,0.198 10 false *f 0.521,3.083 0.729,3.281 0.208,0.198 10 false *e

Push a screwdriver into the hole of the steering column upper with switch bracket assembly shown in the illustration and pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper with switch bracket assembly.

HINT:

Make sure to pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column bracket assembly upper. Failure to do so will affect later work operations.


Text in Illustration
*a Push
*b Pull
*c Claw
*d Stopper
*e LOCK
*f ACC
*g ON
*h START


c.
C119071

Insert a screwdriver into the hole of the steering column upper with switch bracket assembly. Push the screwdriver downward as shown in the illustration to detach the claw of the ignition switch lock cylinder assembly. Pull out the ignition switch lock cylinder assembly.

HINT:

When the ignition lock cylinder assembly detach, a click sound is heard.



Hide 84052 5.REMOVE UNLOCK WARNING SWITCH ASSEMBLY

a.
C155156

Detach the 2 claws and remove the switch.


Hide 85432 6.REMOVE KEY INTERLOCK SOLENOID

a.
C155158

Remove the 2 screws and key interlock solenoid from the switch bracket.


Hide 84450 7.REMOVE IGNITION SWITCH ASSEMBLY

a.
C155157

Detach the 2 claws and remove the ignition switch from the switch bracket.


Hide 45877A 8.REMOVE STEERING COLUMN BRACKET SPACER

a.
F051324

Using a brass bar, hammer and vise, gently strike the central part of the steering column bracket spacer and remove it.


b.

Remove the No. 1 tilt steering support collar from the lower steering column tube.