Home › Steering › POWER STEERING › STEERING GEAR
RM27M0U _55 Steering _049130 POWER STEERING _0234203 STEERING GEAR A

POWER STEERING  STEERING GEAR  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing, coat the parts indicated by the arrows with power steering fluid (See page Steering>POWER STEERING>STEERING GEAR>COMPONENTS).


PROCEDURE

Hide 1.INSTALL RACK STEERING PISTON RING

a.
C003629

Coat a new O-ring with power steering fluid and install it onto the power steering rack.


b.

Expand a new piston ring with your fingers.

NOTICE:

Be careful not to over expand the rack steering piston ring.



c.

Coat a new piston ring with power steering fluid.


d.
N000401

Install the piston ring onto the power steering rack, and position it with your fingers.


Hide 2.INSTALL POWER STEERING CYLINDER TUBE OIL SEAL

a.

Coat a new cylinder tube oil seal lip with power steering fluid.


b.
F051716E02
1.333,0.677 1.792,0.125 1.792,0.125 1.521,0.938 false 1.844,0.021 2.135,0.198 0.292,0.177 10 false SST

Using SST and a press, install the cylinder tube oil seal.

SST
09950-60010  (09951-00280, 09951-00480, 09952-06010)
09950-70010  (09951-07360)

NOTICE:
·

Make sure that the cylinder tube oil seal is installed facing in the correct direction.

·

Take care not to reverse the cylinder tube oil seal direction when installing.




Hide 3.INSTALL POWER STEERING RACK

a.
C353137E01
2.333,3.427 2.615,3.167 false 2.49,1.313 2.219,0.417 2.219,0.417 2.823,1.271 false 1.167,0.25 2.25,0.438 1.083,0.188 10 false Rack Teeth End 2.688,3.073 3.031,3.24 0.344,0.167 10 false SST

Install SST onto the power steering rack.

SST
09631-20111  

HINT:

If necessary, scrape the burrs off the power steering rack teeth end and burnish.



b.

Coat SST with power steering fluid.


c.

Install the power steering rack into the rack housing.


d.

Remove SST.


Hide 4.INSTALL POWER STEERING RACK BUSH

a.
F051717E03
1.219,1.021 1.458,0.844 1.458,0.844 1.292,1.167 false 1.521,0.729 1.813,0.906 0.292,0.177 10 false SST

Using SST and a press, install a new rack bush oil seal onto the rack bush.

SST
09950-60010  (09951-00440)
09950-70010  (09951-07100)

NOTICE:

Make sure that the rack bush oil seal is installed facing the correct direction.



b.

Coat a new O-ring with power steering fluid and install it onto the rack bush.


c.
F005730E10
1.271,1.313 1.042,1.313 false 1.656,1.875 1.438,1.875 false 0.333,1.219 1.01,1.396 0.677,0.177 10 false Vinyl Tape 0.688,1.781 1.375,1.958 0.688,0.177 10 false Rack Bush

To prevent the rack bush oil seal lip from being damaged, wind vinyl tape around the rack end and apply power steering fluid.


d.

Install the rack bush onto the power steering rack.


Hide 5.INSTALL CYLINDER END STOPPER

a.
F051718E02
1.667,0.979 1.958,0.531 false 1.708,1.729 1.385,1.885 false 2.01,0.427 2.313,0.604 0.302,0.177 10 false Wire 0.198,1.865 1.542,2.042 1.344,0.177 10 false Cylinder End Stopper

Align the installation hole for the wire of the cylinder end stopper with the slot of the rack housing.


b.

Install a new wire into the cylinder end stopper.


c.

Using a screwdriver, turn the cylinder end stopper clockwise by 400 to 500°.


Hide 6. AIR TIGHT TEST

a.
F051732E02
0.771,0.885 0.5,1 false 0.146,0.917 0.438,1.094 0.292,0.177 10 false SST

Install SST onto the rack housing.


b.

Apply a vacuum of 53 kPa (400 mmHg, 15.75 in.Hg) for about 30 seconds.


c.

Check that there is no change in the vacuum.

If there is any change in the vacuum, check whether the oil seals are installed correctly.


Hide 7.INSTALL POWER STEERING CONTROL VALVE UPPER OIL SEAL

a.

Coat the control valve upper bearing and a new control valve upper oil seal with power steering fluid.


b.
F051719E02
2.417,1.688 2.521,1.885 2.521,1.885 2.563,1.698 false 2.677,0.885 2.802,0.427 2.802,0.427 2.75,1.417 false 2.406,1.906 2.698,2.083 0.292,0.177 10 false SST 2.844,0.365 3.135,0.542 0.292,0.177 10 false SST

Using SST and a press, install the control valve upper oil seal.

SST
09950-60010  (09951-00180, 09951-00320, 09952-06010)
09950-70010  (09951-07150)


c.
F051720E02
2.688,0.74 2.792,0.469 2.792,0.469 2.75,1.333 false 2.417,1.573 2.625,1.854 2.625,1.854 2.583,1.573 false 2.813,0.365 3.104,0.542 0.292,0.177 10 false SST 2.469,1.865 2.76,2.042 0.292,0.177 10 false SST

Using SST and a press, install the control valve upper bearing.

SST
09950-60010  (09951-00180, 09951-00340, 09952-06010)
09950-70010  (09951-07150)


Hide 8.INSTALL POWER STEERING CONTROL VALVE ASSEMBLY

C003629

a.

Expand 4 new control valve rings with your fingers.

NOTICE:

Be careful not to over expand the control valve rings.



b.

Coat the 4 control valve rings with power steering fluid.


c.

Install the 4 control valve rings onto the control valve, and position them with your fingers.


d.
F051721E02
1.156,0.469 1.521,0.292 1.521,0.292 1.823,0.792 false 2.125,1.333 2.479,1.667 2.479,1.667 2.219,1.313 false 2.354,1.25 2.479,1.656 2.479,1.656 2.469,1.177 false 1.594,0.188 1.885,0.365 0.292,0.177 10 false SST 1.854,1.677 3.104,1.854 1.25,0.177 10 false Control Valve RIngs

Carefully slide the tapered end of SST over the control valve rings until they fit to the control valve.

SST
09631-20081  

NOTICE:

Be careful not to damage the control valve rings.



e.
F051722E02
1.542,0.948 1.948,0.635 false 1.99,0.542 2.667,0.719 0.677,0.177 10 false Vinyl Tape

To prevent the control valve upper oil seal lip from getting damaged, wind vinyl tape around the serrated portion of the control valve.


f.

Coat the control valve upper oil seal lip with power steering fluid.


g.

Install the control valve onto the control valve housing.

NOTICE:

Be careful not to damage the control valve ring and control valve upper oil seal lip.



h.

Apply grease to the needle roller bearing.


i.

Install a new O-ring onto the control valve housing.


j.

Wind vinyl tape around the serrated portion of the control valve.


k.
G100343

Install the control valve w/ control valve housing onto the rack housing with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 14 ft.*lbf)


Hide 9.INSTALL STEERING GEAR RACK GUIDE

a.

Install the rack guide.


b.

Install the rack guide spring.


c.

Apply adhesive to 2 or 3 threads of the rack guide spring cap.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Provisionally install the rack guide spring cap.


Hide 10.ADJUST TOTAL PRELOAD

a.

To prevent the steering rack teeth from damaging the oil seal lip, provisionally install the RH and LH steering rack end.


b.

Using 32 mm hexagon wrench, torque the rack guide spring cap.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


c.
C206205

Using 32 mm hexagon wrench, loosen the rack guide spring cap.


d.
F051725E02
0.583,0.635 0.833,0.49 false 0.865,0.385 1.156,0.563 0.292,0.177 10 false SST

Using SST, turn the control valve to the right and left once or twice.

SST
09616-00011  


e.

Using SST, loosen the rack guide spring cap until the rack guide spring ceases to function.


f.
C131752E04
2.198,0.573 2.125,0.156 false 2.125,0.156 2.021,0.156 false 1.563,1.396 1.479,0.177 false 1.479,0.177 1.333,0.177 false 1.677,0.052 2,0.25 0.323,0.198 10 false SST 0.24,0.063 1.344,0.385 1.104,0.323 10 true 32 mm Hexagon Wrench

Using SST, a torque wrench and 32 mm hexagon wrench, tighten the cap until the preload is within the specification.

SST
09616-00011  

Preload (turning):

1.9 to 2.7 N*m (19.4 to 27.5 kgf*cm, 16.8 to 23.9 in.*lbf)



g.

Apply adhesive to 2 or 3 threads of the rack guide spring cap nut.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



h.

Provisionally install the rack guide spring cap nut.


i.
C131753E01
1.01,0.046 2.018,0.207 1.008,0.161 10 Fulcrum Length 2.269,0.556 2.596,0.721 0.327,0.165 10 SST 1.747,0.934 2.028,0.659 false 2.028,0.659 2.211,0.659 false

Using SST, hold the rack guide spring cap and using 32 mm hexagon wrench, torque the rack guide spring cap nut.

SST
09922-10010  

Torque:
without SST : 85 N*m (867 kgf*cm, 63 ft.*lbf)
with SST : 62 N*m (632 kgf*cm, 46 ft.*lbf)

NOTICE:

Turn SST 09922-10010 in the direction shown in the illustration.


HINT:

Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).



j.

Recheck the total preload.

Preload (turning):

1.9 to 2.7 N*m (19.4 to 27.5 kgf*cm, 16.8 to 23.9 in.*lbf)



k.

Remove the RH and LH steering rack ends.


l.
F051728E02
1.354,1.219 1.125,0.865 1.125,0.865 1.844,1.219 false 0.292,0.719 1.01,0.896 0.719,0.177 10 false MP Grease

Apply MP grease to the control valve as shown in the illustration.


m.
F051708E02
0.802,0.375 1.177,0.125 false 1.208,0.021 1.885,0.198 0.677,0.177 10 false Vinyl Tape

Wind vinyl tape around the serrated portion of the control valve.


n.

Install the dust cover onto the control valve housing.


Hide 11.INSTALL STEERING RACK END SUB-ASSEMBLY

a.
C353138E01
1.646,1.5 1.719,1.229 false 2.573,1.469 2.813,1.396 false 2.396,3.719 2.667,3.75 false 2.042,4.021 2.01,4.156 false 0.219,0.844 0.802,1.198 0.583,0.354 10 false Fulcrum Length 1.76,1.115 2.125,1.292 0.365,0.177 10 false SST 2.854,1.323 3.219,1.5 0.365,0.177 10 false SST 2.719,3.698 3.083,3.875 0.365,0.177 10 false SST 1.854,4.188 2.219,4.365 0.365,0.177 10 false SST

Install 2 new claw washers, and provisionally install the 2 steering rack ends.

HINT:

Align the claws of the claw washers with the power steering rack grooves.



b.

Using 2 SST, install the 2 steering rack ends.

SST
09922-10010  

Torque:
without SST : 195 N*m (1988 kgf*cm, 144 ft.*lbf)
with SST : 142 N*m (1448 kgf*cm, 105 ft.*lbf)

NOTICE:

Turn SST 09922-10010 in the direction shown in the illustration.


HINT:
·

Using SST, hold the power steering rack and install the rack end sub-assembly.

·

Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).




c.
C035928

Using a brass bar and hammer, stake the 2 claw washers.

NOTICE:

Avoid any impact to the power steering rack.



Hide 12.INSPECT STEERING RACK END SUB-ASSEMBLY

a.
F051730

Ensure that the steering rack end hole is not clogged with grease.

HINT:

If the hole is clogged, the pressure inside the boot will change after it has been assembled, when the steering wheel is turned.



Hide 45535 13.INSTALL STEERING RACK BOOT NO. 1

Hide 45536 14.INSTALL STEERING RACK BOOT NO. 2

Hide 45535D 15.INSTALL STEERING RACK BOOT NO. 1 CLAMP

a.
F051731E02
1.844,0.24 1.948,0.74 false 1.552,0.135 1.844,0.313 0.292,0.177 10 false SST

Using SST, tighten the rack boot No. 1 clamp as shown in the illustration.

SST
09521-24010  

Clearance:

3.0 mm (0.118 in.) or less


NOTICE:

Be careful not to damage the rack boot No. 1.



Hide 45536A 16.INSTALL STEERING RACK BOOT NO. 2 CLAMP

HINT:

The installation procedure for the No. 2 side is the same as that for the No. 1 side.


Hide 45535B 17.INSTALL STEERING RACK BOOT CLIP

a.
U152126E02
1.479,0.021 2.031,0.208 0.552,0.188 10 true Upward 0.177,0.51 0.698,0.885 0.521,0.375 10 false Front of Vehicle

Using pliers, install the 2 rack boot clips.

NOTICE:

Make sure that each clip's claws are positioned within the area shown in the illustration.



Hide 18.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.

Align the matchmarks of the tie rod and rack end and temporarily install the tie rod with the lock nut.


b.
C154516E01
1.739,0.107 2.493,0.266 0.754,0.159 10 Matchmark 0.906,0.642 0.906,0.203 false 0.906,0.203 1.709,0.203 false 1.127,0.777 1.127,0.203 false

After adjusting toe-in, torque the nut.

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)


Hide 19.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

The installation procedure for the RH side is the same as that for the LH side.


Hide 20.INSTALL STEERING TURN PRESSURE TUBE

a.

Coat 4 new O-rings with power steering fluid and install them onto the pressure tubes.


b.
F051696E04
1.927,1.135 2.188,0.656 2.188,0.656 2.354,0.656 false 2.469,0.583 3.146,0.958 0.677,0.375 10 false Union Nut Wrench 0.948,0.083 1.5,0.448 0.552,0.365 10 false Fulcrum Length

Using union nut wrench, install the 2 pressure tubes.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Use the formula calculate special torque values for situations for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).