CHECK OCCUPANT CLASSIFICATION ECU
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specification |
|---|---|---|---|---|
| Y2-1 (+B) - Y2-3 (GND) | W - W-B | Battery | Ignition switch ON | 11 to 14 V |
| Y2-2 (DIA) - Y2-3 (GND) | GR - W-B | Diagnosis (DLC3) | Ignition switch ON | Pulse generation |
| Y2-3 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Y2-4 (FSR-) - Y2-3 (GND) | Y - W-B | Center airbag sensor communication ground line | Always | Below 1 Ω |
| Y2-5 (BGND) - Y2-3 (GND) | P - W-B | Passenger side buckle switch ground line | Always | Below 1 Ω |
| Y2-7 (IG2) - Y2-3 (GND) | B - W-B | Power source (IGN fuse) | Ignition switch ON | 11 to 14 V |
| Y2-8 (FSR+) - Y2-4 (FSR-) | L - Y | Center airbag sensor communication line | Ignition switch ON | Pulse generation |
| Y2-9 (BSW) - Y2-5 (BGND) | G - P | Passenger side buckle switch line | Ignition switch ON, buckle switch ON | 0.12 to 0.18 A |
| Ignition switch ON, buckle switch OFF | 0.4 to 0.7 mA | |||
| Y1-1 (SGD1) - Y2-3 (GND) | G - W-B | Front occupant detection sensor LH ground line | Always | Below 1 Ω |
| Y1-2 (SGD2) - Y2-3 (GND) | O - W-B | Front occupant detection sensor RH ground line | Always | Below 1 Ω |
| Y1-3 (SGD3) - Y2-3 (GND) | W - W-B | Rear occupant detection sensor LH ground line | Always | Below 1 Ω |
| Y1-4 (SGD4) - Y2-3 (GND) | BR - W-B | Rear occupant detection sensor RH ground line | Always | Below 1 Ω |
| Y1-11 (SVC1) - Y1-1 (SGD1) | R - G | Front occupant detection sensor LH power supply line | Ignition switch ON, load is applied to front occupant detection sensor LH | 4.5 to 5.1 V |
| Y1-12 (SVC2) - Y1-2 (SGD2) | W - O | Front occupant detection sensor RH power supply line | Ignition switch ON, load is applied to front occupant detection sensor RH | 4.5 to 5.1 V |
| Y1-5 (SVC3) - Y1-3 (SGD3) | GR - W | Rear occupant detection sensor LH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor LH | 4.5 to 5.1 V |
| Y1-6 (SVC4) - Y1-4 (SGD4) | V - BR | Rear occupant detection sensor RH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor RH | 4.5 to 5.1 V |
| Y1-7 (SIG1) - Y1-1 (SGD1) | P - G | Front occupant detection sensor LH signal line | Ignition switch ON, load is applied to front occupant detection sensor LH | Pulse generation |
| Y1-8 (SIG2) - Y1-2 (SGD2) | L - O | Front occupant detection sensor RH signal line | Ignition switch ON, load is applied to front occupant detection sensor RH | Pulse generation |
| Y1-9 (SIG3) - Y1-3 (SGD3) | Y - W | Rear occupant detection sensor LH signal line | Ignition switch ON, load is applied to rear occupant detection sensor LH | Pulse generation |
| Y1-10 (SIG4) - Y1-4 (SGD4) | B - BR | Rear occupant detection sensor RH signal line | Ignition switch ON, load is applied to rear occupant detection sensor RH | Pulse generation |
If the result is not as specified, the ECU may have a malfunction.