Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM27M0U _58 Vehicle Interior _049132 SEAT BELT _0234223 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


a.

Disconnect the J28 combination meter assembly connector.

U152798E02
3.469,0.292 3.802,0.479 0.333,0.188 10 false J28


b.

Disconnect the J28 combination meter assembly connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J28-2 (IG+) - Body ground P - Body ground Ignition power supply
(IG signal)
Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
J28-1 (B) - Body ground LG - Body ground Battery power supply Always 11 to 14 V
J28-24 (ES) - Body ground W-B - Body ground Ground Always Below 1 Ω


d.

Reconnect the J28 combination meter assembly connector.


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J28-30 (SI) - Body ground LG - Body ground Speed signal (input) Ignition switch ON, wheel turned slowly Pulse generation



CHECK CENTER AIRBAG SENSOR ASSEMBLY


U152125E02
2.594,0.552 2.844,0.729 0.25,0.177 10 false J46 3.896,0.552 4.115,0.76 0.219,0.208 10 false P1 4.865,0.552 5.094,0.74 0.229,0.188 10 false Q1

Terminal No. Terminal Symbol Destination
P1-11 DBE+ Front seat inner belt assembly LH
P1-12 DBE- Front seat inner belt assembly LH
Q1-12 FSP+ Occupant detection ECU
Q1-13 FSP- Occupant detection ECU


CHECK OCCUPANT DETECTION ECU


a.

Measure the voltage according to the value(s) in the table below.

U152944E02
2.698,0.073 2.896,0.25 0.198,0.177 10 false Y1 4.323,0.073 4.542,0.25 0.219,0.177 10 false Y2

HINT:

Since the occupant detection ECU uses waterproof connectors, the voltage and waveform cannot be inspected directly. Standard voltage readings and waveforms are indicated for reference only.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specification
Y2-1 (+B) - Y2-3 (GND) W - W-B Battery Ignition switch ON 11 to 14 V
Y2-2 (DIA) - Y2-3 (GND) GR - W-B Diagnosis (DLC3) Ignition switch ON Pulse generation
Y2-3 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
Y2-4 (FSR-) - Y2-3 (GND) Y - W-B Center airbag sensor communication ground line Always Below 1 Ω
Y2-5 (BGND) - Y2-3 (GND) P - W-B Passenger side buckle switch ground line Always Below 1 Ω
Y2-7 (IG2) - Y2-3 (GND) B - W-B Power source (IGN fuse) Ignition switch ON 11 to 14 V
Y2-8 (FSR+) - Y2-4 (FSR-) L - Y Center airbag sensor communication line Ignition switch ON Pulse generation
Y2-9 (BSW) - Y2-5 (BGND) G - P Passenger side buckle switch line Ignition switch ON, buckle switch ON 0.12 to 0.18 A
Ignition switch ON, buckle switch OFF 0.4 to 0.7 mA
Y1-1 (SGD1) - Y2-3 (GND) G - W-B Front occupant detection sensor LH ground line Always Below 1 Ω
Y1-2 (SGD2) - Y2-3 (GND) O - W-B Front occupant detection sensor RH ground line Always Below 1 Ω
Y1-3 (SGD3) - Y2-3 (GND) W - W-B Rear occupant detection sensor LH ground line Always Below 1 Ω
Y1-4 (SGD4) - Y2-3 (GND) BR - W-B Rear occupant detection sensor RH ground line Always Below 1 Ω
Y1-11 (SVC1) - Y1-1 (SGD1) R - G Front occupant detection sensor LH power supply line Ignition switch ON, load is applied to front occupant detection sensor LH 4.5 to 5.1 V
Y1-12 (SVC2) - Y1-2 (SGD2) W - O Front occupant detection sensor RH power supply line Ignition switch ON, load is applied to front occupant detection sensor RH 4.5 to 5.1 V
Y1-5 (SVC3) - Y1-3 (SGD3) GR - W Rear occupant detection sensor LH power supply line Ignition switch ON, load is applied to rear occupant detection sensor LH 4.5 to 5.1 V
Y1-6 (SVC4) - Y1-4 (SGD4) V - BR Rear occupant detection sensor RH power supply line Ignition switch ON, load is applied to rear occupant detection sensor RH 4.5 to 5.1 V
Y1-7 (SIG1) - Y1-1 (SGD1) P - G Front occupant detection sensor LH signal line Ignition switch ON, load is applied to front occupant detection sensor LH Pulse generation
Y1-8 (SIG2) - Y1-2 (SGD2) L - O Front occupant detection sensor RH signal line Ignition switch ON, load is applied to front occupant detection sensor RH Pulse generation
Y1-9 (SIG3) - Y1-3 (SGD3) Y - W Rear occupant detection sensor LH signal line Ignition switch ON, load is applied to rear occupant detection sensor LH Pulse generation
Y1-10 (SIG4) - Y1-4 (SGD4) B - BR Rear occupant detection sensor RH signal line Ignition switch ON, load is applied to rear occupant detection sensor RH Pulse generation