Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY
RM27M0U _58 Vehicle Interior _049132 SEAT BELT _0234225 FRONT SEAT INNER BELT ASSEMBLY G

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 73240 1.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH (for Manual Seat)

a.
B356559E04
1.844,0.979 2.51,0.854 true 0.917,0.854 1.583,0.979 true 0.125,0.083 0.313,0.24 0.188,0.156 10 false *a 0.854,0.333 1.042,0.49 0.188,0.156 10 false *1 0.854,2.229 1.042,2.385 0.188,0.156 10 false *2 2.583,0.75 3.156,1 0.573,0.25 10 false LSP- 0.51,0.771 1.083,1.021 0.573,0.25 10 false LSP+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (LSP+) - B-1 Always Below 1 Ω
A-4 (LSP-) - B-2 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly LH.

Text in Illustration
*1 Connector A
*2 Connector B
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)


Hide 73240 2.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH (for Power Seat)

a.
B356559E04
1.844,0.979 2.51,0.854 true 0.917,0.854 1.583,0.979 true 0.125,0.083 0.313,0.24 0.188,0.156 10 false *a 0.854,0.333 1.042,0.49 0.188,0.156 10 false *1 0.854,2.229 1.042,2.385 0.188,0.156 10 false *2 2.583,0.75 3.156,1 0.573,0.25 10 false LSP- 0.51,0.771 1.083,1.021 0.573,0.25 10 false LSP+

for 8 Way Seat Type:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (LSP+) - B-1 Always Below 1 Ω
A-4 (LSP-) - B-2 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly LH.

Text in Illustration
*1 Connector A
*2 Connector B
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)


b.
B356559E05
1.844,0.979 2.51,0.854 true 0.917,0.854 1.583,0.979 true 0.927,1.375 1.583,1.208 true 1.865,1.208 2.531,1.344 true 0.115,0.083 0.302,0.24 0.188,0.156 10 false *a 0.854,0.333 1.042,0.49 0.188,0.156 10 false *1 0.854,2.229 1.042,2.385 0.188,0.156 10 false *2 2.573,0.74 3.146,0.99 0.573,0.25 10 false LSP- 0.49,0.76 1.063,1.01 0.573,0.25 10 false LSP+ 0.573,1.323 0.958,1.552 0.385,0.229 10 false RDC 2.594,1.271 2.844,1.51 0.25,0.24 10 false E

for 10 Way Seat Type:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (LSP+) - B-1 Always Below 1 Ω
A-4 (LSP-) - B-2 Always Below 1 Ω
A-5 (RDC) - A-6 (E) Seat belt unfastened Below 1 Ω
A-5 (RDC) - A-6 (E) Seat belt fastened 10 kΩ or higher


If the result is not as specified, replace the front seat inner belt assembly LH.

Text in Illustration
*1 Connector A
*2 Connector B
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)


Hide 73230 3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

a.

Connect the battery and an ammeter to the front seat inner belt assembly RH connector.


b.
B356560E03
0.948,1.375 0.583,0.833 true 1.313,1.396 1.677,0.854 true 0.198,0.125 0.406,0.313 0.208,0.188 10 false *a 1.729,0.76 2.219,0.958 0.49,0.198 10 false RBE+ 0.188,0.771 0.677,0.969 0.49,0.198 10 false RBE-

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (RBE+) - 2 (RBE-) Battery voltage is 12V
Seat belt unfastened
4.0 to 7.0 mA
1 (RBE+) - 2 (RBE-) Battery voltage is 12V
Seat belt fastened
12 to 18 mA


If the result is not as specified, replace the front seat inner belt assembly RH.

Text in Illustration
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)