Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM
RM27M0U _58 Vehicle Interior _049133 LIGHTING _0234252 LIGHTING SYSTEM J

LIGHTING  LIGHTING SYSTEM  Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU receives a door open/closed signal from each door courtesy light switch.

WIRING DIAGRAM

E146142E01
5.817,4.844 6.843,4.991 1.026,0.147 10 Main Body ECU 5.885,3.071 6.557,3.215 0.672,0.145 10 LCTY 5.885,1.954 6.557,2.099 0.672,0.145 10 PCTY 5.885,0.82 6.557,0.964 0.672,0.145 10 DCTY 5.885,4.205 6.557,4.350 0.672,0.145 10 RRCY 5.556,0.829 5.740,0.980 0.184,0.151 10 J4 5.556,1.756 5.740,1.907 0.184,0.151 10 21 5.556,1.941 5.740,2.092 0.184,0.151 10 J3 5.556,0.645 5.740,0.796 0.184,0.151 10 24 5.544,3.079 5.769,3.230 0.225,0.151 10 DC 5.556,4.022 5.740,4.173 0.184,0.151 10 25 5.556,4.206 5.740,4.358 0.184,0.151 10 J3 5.588,2.898 5.686,3.050 0.098,0.151 10 2 3.68,3.188 3.801,3.352 0.121,0.164 10 1 3.68,4.302 3.801,4.466 0.121,0.164 10 1 3.68,0.942 3.801,1.106 0.121,0.164 10 1 3.68,2.056 3.801,2.220 0.121,0.164 10 1 2.039,4.466 4.352,4.622 2.313,0.156 10 Q6 2.039,3.494 4.352,3.650 2.313,0.156 10 Rear Door Courtesy Light Switch LH 2.039,3.354 4.352,3.510 2.313,0.156 10 P6 2.039,2.36 4.352,2.515 2.313,0.156 10 Front Door Courtesy Light Switch RH 2.039,2.219 4.352,2.375 2.313,0.156 10 Q5 2.039,1.248 4.352,1.404 2.313,0.156 10 Front Door Courtesy Light Switch LH 2.039,1.108 4.352,1.264 2.313,0.156 10 P5 2.039,4.606 4.352,4.762 2.313,0.156 10 Rear Door Courtesy Light Switch RH

PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR COURTESY LIGHT SWITCH)
a.

Operate the Techstream according to the display and select the "Data List".

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Front door courtesy light switch LH signal / ON or OFF ON: Front door courtesy light switch LH on
OFF: Front door courtesy light switch LH off
-
P Door Courtesy SW Front door courtesy light switch RH signal / ON or OFF ON: Front door courtesy light switch RH on
OFF: Front door courtesy light switch RH off
-
RL Door Courtesy SW Rear door courtesy light switch LH signal / ON or OFF ON: Rear door courtesy light switch LH on
OFF: Rear door courtesy light switch LH off
-
RR Door Courtesy SW Rear door courtesy light switch RH signal / ON or OFF ON: Rear door courtesy light switch RH on
OFF: Rear door courtesy light switch RH off
-

Result
Result Proceed to
OK A
NG (Front door courtesy light switch LH does not operate) B
NG (Front door courtesy light switch RH does not operate) C
NG (Rear door courtesy light switch LH does not operate) D
NG (Rear door courtesy light switch RH does not operate) E



A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH

C

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH

D

6.INSPECT REAR DOOR COURTESY LIGHT SWITCH LH

E

8.INSPECT REAR DOOR COURTESY LIGHT SWITCH RH
2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH
E142907E03
1.679,3.644 1.779,3.800 0.100,0.156 10 1 2.329,0.557 2.985,0.713 0.656,0.156 10 Pushed 2.329,0.156 3.156,0.312 0.827,0.156 10 Not Pushed 0.082,2.286 2.784,2.623 2.702,0.336 10 Component without harness connected: (Front Door Courtesy Light Switch LH) 0.241,1.866 1.049,2.036 0.809,0.170 10 Body ground 1.051,1.208 0.624,1.875 false

a.

Remove the front door courtesy light switch LH (see page Vehicle Interior>LIGHTING>FRONT DOOR COURTESY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Not pushed Below 1 Ω
Pushed 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH LH

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)
U152727E01
0.042,0.034 2.576,0.375 2.534,0.341 10 Front view of wire harness connector: (to Front Door Courtesy Light Switch LH) 0.042,2.486 2.576,2.827 2.534,0.341 10 Front view of wire harness connector: (to Main Body ECU) 0.446,3.897 0.646,4.062 0.200,0.165 10 J4 0.64,1.76 0.840,1.925 0.200,0.165 10 P5 2.095,4.301 2.649,4.184 false 2.666,4.098 3.081,4.249 0.415,0.151 10 DCTY

a.

Disconnect the P5 switch connector.


b.

Disconnect the J4 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P5-1 - J4-24 (DCTY) Always Below 1 Ω
P5-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH
E142907E04
1.661,3.627 1.762,3.782 0.100,0.156 10 1 2.295,0.574 2.950,0.730 0.656,0.156 10 Pushed 2.295,0.173 3.122,0.329 0.827,0.156 10 Not Pushed 0.099,2.326 2.588,2.662 2.489,0.336 10 Component without harness connected: (Front Door Courtesy Light Switch RH) 0.261,1.777 1.069,1.947 0.809,0.170 10 Body ground 1.03,1.238 0.624,1.783 false

a.

Remove the front door courtesy light switch RH (see page Vehicle Interior>LIGHTING>FRONT DOOR COURTESY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Not pushed Below 1 Ω
Pushed 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH RH

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)
U152729E01
0.042,0.015 2.627,0.356 2.585,0.341 10 Front view of wire harness connector: (to Front Door Courtesy Light Switch RH) 0.042,2.502 2.576,2.843 2.534,0.341 10 Front view of wire harness connector: (to Main Body ECU) 0.546,3.781 0.765,3.946 0.218,0.165 10 J3 0.631,1.737 0.835,1.902 0.205,0.165 10 Q5 0.392,4.365 0.806,4.517 0.415,0.151 10 PCTY 0.884,4.44 1.137,4.144 false

a.

Disconnect the Q5 switch connector.


b.

Disconnect the J3 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q5-1 - J3-21 (PCTY) Always Below 1 Ω
Q5-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR DOOR COURTESY LIGHT SWITCH LH
E142907E05
1.679,3.661 1.779,3.817 0.100,0.156 10 1 2.243,0.574 2.899,0.730 0.656,0.156 10 Pushed 2.243,0.173 3.070,0.329 0.827,0.156 10 Not Pushed 0.14,2.293 2.630,2.629 2.489,0.336 10 Component without harness connected: (Rear Door Courtesy Light Switch LH) 0.249,1.921 1.058,2.090 0.809,0.170 10 Body ground 1.013,1.239 0.587,1.921 false

a.

Remove the rear door courtesy light switch LH (see page Vehicle Interior>LIGHTING>REAR DOOR COURTESY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Not pushed Below 1 Ω
Pushed 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH LH

7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)
U152799E02
0.896,3.552 1.188,3.26 true 0.083,0.063 2.542,0.75 2.458,0.688 10 false Front view of wire harness connector: (to Rear Door Courtesy Light Switch LH) 0.083,2.396 2.542,3.063 2.458,0.667 10 false Front view of wire harness connector: (to Main Body ECU) 0.604,1.865 0.802,2.052 0.198,0.188 10 false P6 0.177,3.719 0.438,3.906 0.26,0.188 10 false DC 1.25,3.125 1.688,3.313 0.438,0.188 10 false LCTY

a.

Disconnect the P6 switch connector.


b.

Disconnect the DC ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P6-1 - DC-2 (LCTY) Always Below 1 Ω
P6-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR DOOR COURTESY LIGHT SWITCH RH
E142907E06
1.679,3.644 1.779,3.800 0.100,0.156 10 1 2.26,0.574 2.916,0.730 0.656,0.156 10 Pushed 2.26,0.173 3.087,0.329 0.827,0.156 10 Not Pushed 0.049,2.293 2.538,2.629 2.489,0.336 10 Component without harness connected: (Rear Door Courtesy Light Switch RH) 0.14,1.812 0.949,1.982 0.809,0.170 10 Body ground 1.028,1.215 0.527,1.812 false

a.

Remove the rear door courtesy light switch RH (see page Vehicle Interior>LIGHTING>REAR DOOR COURTESY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Not pushed Below 1 Ω
Pushed 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH RH

9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)
U152730E01
0.042,0.015 2.627,0.356 2.585,0.341 10 Front view of wire harness connector: (to Rear Door Courtesy Light Switch RH) 0.042,2.502 2.576,2.843 2.534,0.341 10 Front view of wire harness connector: (to Main Body ECU) 0.546,3.781 0.765,3.946 0.218,0.165 10 J3 0.631,1.737 0.835,1.902 0.205,0.165 10 Q6 0.392,4.365 0.806,4.517 0.415,0.151 10 RRCY 0.884,4.44 1.897,4.153 false

a.

Disconnect the Q6 switch connector.


b.

Disconnect the J3 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q6-1 - J3-25 (RRCY) Always Below 1 Ω
Q6-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR