Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM
RM27M0U _58 Vehicle Interior _049133 LIGHTING _0234252 LIGHTING SYSTEM J

LIGHTING  LIGHTING SYSTEM  Taillight Circuit  


DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM

E146812E02
2.001,4.089 2.755,4.257 0.753,0.167 10 R4 1.084,2.909 1.825,3.076 0.742,0.167 10 Taillight LH 1.084,2.732 1.929,2.899 0.846,0.167 10 R5 1.998,4.247 2.752,4.414 0.753,0.167 10 Taillight RH 4.719,3.885 5.088,4.050 0.369,0.165 10 TAIL 4.887,1.839 5.214,2.000 0.327,0.161 10 TAIL 0.149,1.027 0.967,1.206 0.818,0.179 10 from Battery 6.375,1.041 6.782,1.191 0.407,0.150 10 TRLY 4.941,4.193 5.967,4.335 1.026,0.142 10 Main Body ECU 3.631,3.732 3.859,3.874 0.228,0.142 10 DB 3.687,3.544 3.830,3.686 0.143,0.142 10 8 3.687,0.868 3.830,1.010 0.143,0.142 10 1 3.631,1.042 3.859,1.184 0.228,0.142 10 DA 1.692,2.448 1.914,2.621 0.222,0.173 10 TL 1.959,2.448 2.097,2.621 0.139,0.173 10 1 1.124,2.45 1.271,2.652 0.147,0.203 10 E 1.781,3.815 1.929,4.017 0.147,0.203 10 2 2.555,3.813 2.777,3.986 0.222,0.173 10 TL 2.822,3.813 2.960,3.986 0.139,0.173 10 1 1.987,3.815 2.134,4.017 0.147,0.203 10 E 0.918,2.45 1.066,2.652 0.147,0.203 10 2

CAUTION / NOTICE / HINT

HINT:

Inspect the bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TAILLIGHT)
a.

Operate the Techstream according to the steps on the display and select "Active Test".

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight ON or OFF -

OK:

Taillight turns on / turns off.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (TAIL)
2.INSPECT FUSE (TAIL)
a.

Remove the TAIL fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
TAIL fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TAILLIGHT - BATTERY)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (TAILLIGHT - BATTERY)
U152898E01
0.099,0.06 2.498,0.382 2.399,0.323 10 Front view of wire harness connector: (to Taillight LH) 0.49,1.422 0.746,1.567 0.257,0.145 10 R5 0.556,1.826 0.813,1.972 0.257,0.145 10 TL 0.802,1.897 1.372,1.674 false

a.

for LH:

i.

Disconnect the R5 taillight connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
R5-1 (TL) - Body ground Light control switch TAIL 11 to 14 V
Light control switch except TAIL Below 1 V




U152899E01
0.099,0.06 2.498,0.382 2.399,0.323 10 Front view of wire harness connector: (to Taillight RH) 0.49,1.422 0.746,1.567 0.257,0.145 10 R4 0.556,1.826 0.813,1.972 0.257,0.145 10 TL 0.802,1.897 1.372,1.674 false

b.

for RH:

i.

Disconnect the R4 taillight connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
R4-1 (TL) - Body ground Light control switch TAIL 11 to 14 V
Light control switch except TAIL Below 1 V





OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TAILLIGHT - BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
U152779E02
0.156,0.031 2.542,0.385 2.385,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 0.75,2.208 0.958,2.375 0.208,0.167 10 false DA

a.

Disconnect the DA ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
DA-1 - Body ground Always 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (TAILLIGHT - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TAILLIGHT - MAIN BODY ECU)
U152897E01
0.767,0.093 3.152,0.450 2.385,0.357 10 Front view of wire harness connector: (to Main Body ECU) 0.683,1.646 0.895,1.816 0.211,0.170 10 DB 4.341,1.897 4.552,2.067 0.211,0.170 10 R4 4.341,1.498 4.552,1.668 0.211,0.170 10 R5 4.642,1.897 4.854,2.067 0.211,0.170 10 *2 4.642,1.498 4.854,1.668 0.211,0.170 10 *1 4.328,0.082 6.656,0.432 2.328,0.350 10 Front view of wire harness connector: (to Taillight) 4.634,2.314 4.853,2.463 0.218,0.149 10 TL 5.279,1.921 4.872,2.37 false 0.11,2.136 0.757,2.315 0.647,0.179 10 *1: for LH 0.11,2.426 0.757,2.605 0.647,0.179 10 *2: for RH

*1: for LH

*2: for RH

a.

Disconnect the DB ECU connector.


b.

Disconnect the R5*1 and R4*2 taillight connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
R5-1 (TL) - DB-8*1 Always Below 1 Ω
R5-1 (TL) - Body ground*1 Always 10 kΩ or higher
R4-1 (TL) - DB-8*2 Always Below 1 Ω
R4-1 (TL) - Body ground*2 Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR