CUSTOMIZING FUNCTION WITH TECHSTREAM
The following items can be customized.
When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.
Customizing with the Techstream.
Connect the Techstream to the DLC3.
Turn the ignition switch ON.
Turn the Techstream on.
Enter the following menus: Customize Setting.
Select the setting by referring to the table below.
| Display | Default | Contents | Setting |
|---|---|---|---|
| I/L when ACC OFF | ON | Illuminates light when ignition switch turned to ACC
(Room light illuminated when interior light switch set to DOOR) |
ON / OFF |
| Lighting Time | 15s | Changes illumination duration after door closure
(It will quickly fade out when turning ignition switch ON) |
7.5s / 15s / 30s |
| I/L ON W/Door key Unlock | ON | Function to light up room light when unlocking with door key cylinder
(Room light illuminated when interior light switch set to DOOR) |
ON / OFF |
| Light Auto OFF Delay | 30s | Function to continue illuminating headlight for certain period of time after closing all doors with ignition switch turned from ON to OFF under condition that light control switch is at HEAD or AUTO with the headlight ON | OFF / 30s / 60s / 90s |
| Interior Light Control | ON | This function controls the interior lights. | ON / OFF |
| Sensitivity | NORMAL | Function to adjust ambient light sensitivity of automatic light control system*1 | LIGHT2 / LIGHT1 / NORMAL / DARK1 / DARK2 |
| Disp Ex ON Sen | NORMAL | Function to change level of ambient light at which system dims lights such as combination meter indicator light, A/C indicator light and clock light*2 | LIGHT2 / LIGHT1 / NORMAL / DARK1 / DARK2 |
| Disp Ex OFF Sen | NORMAL | Function to change level of ambient light at which system cancels dimming of lights such as combination meter indicator light, A/C indicator light and clock light*3 | LIGHT2 / LIGHT1 / NORMAL / DARK1 / DARK2 |
The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.
When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.
When the setting is closer to the "Light" side, the system dims the indicator lights even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before dimming the indicator lights.
When the setting is closer to the "Dark" side, the system cancels the dimming of the indicator lights even when the surrounding area is relatively dark. When the setting is closer to the "Light" side, the system waits until the surrounding area is brighter before canceling the dimming of the indicator lights.
Customizing with Multi-display.
Turn the ignition switch ON.
Enter the following menus: Setup / Vehicle / Vehicle Settings / Vehicle Customization / Light Settings.
Select the setting by referring to the table below.
| Display | Default | Contents | Setting | Relevant ECU |
|---|---|---|---|---|
| Interior Lights Off Time | 15 s | This function controls the interior lights. | OFF, 7.5 s, 15 s or 30 s | Main body ECU (Driver side junction block |
| Light Sensor Sensitivity | 0
(middle bar) |
Adjusts the ambient light sensitivity of the automatic light control system.* | -2, -1, 0, +1 or +2 | |
| Headlights Off Time | 30 s | Function to continue illuminating headlights and taillights for a certain period of time after closing driver door with the ignition switch turned from ON to off under the condition that the headlight dimmer switch is in the AUTO position with the headlights and taillights on. | OFF, 30 s, 60 s or 90 s |
The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.
When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.