The main body ECU receives light control switch and dimmer switch information signals from the headlight dimmer switch, and illuminates the headlight high beam.
Inspect the bulbs for circuits related to this system before performing the following inspection procedure.
Operate the Techstream according to the steps on the display and select "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Head Light Hi | Headlight (High) | ON or OFF | - |
Headlight (High) turns on / turns off.
OK
NG
Remove the HEAD LH and HEAD RH fuses from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| HEAD LH fuse | Always | Below 1 Ω |
| HEAD RH fuse |
OK
NG
for LH:
Disconnect the A8 headlight connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A8-2 (HI) - Body ground | Light control switch HEAD, dimmer switch High | 11 to 14 V |
| Light control switch HEAD, dimmer switch except High | Below 1 V |
for RH:
Disconnect the A9 headlight connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A9-2 (HI) - Body ground | Light control switch HEAD, dimmer switch High | 11 to 14 V |
| Light control switch HEAD, dimmer switch except High | Below 1 V |
OK
NG
Remove the headlight dimmer relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω | |
| 3 - 4 | Battery voltage not applied to terminals 1 and 2 | Below 1 Ω |
| Battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
OK
NG
Remove the headlight dimmer relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Headlight dimmer relay terminal 1 - Body ground | Light control switch HEAD, dimmer switch High | 11 to 14 V |
| Headlight dimmer relay terminal 3 - Body ground | Light control switch HEAD, dimmer switch High |
OK
NG
Remove the headlight dimmer relay from the engine room relay block.
for LH:
Disconnect the A8 headlight connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Headlight dimmer relay terminal 5 - A8-2 (HI) | Always | Below 1 Ω |
| Headlight dimmer relay terminal 5 - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the A9 headlight connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Headlight dimmer relay terminal 5 - A9-2 (HI) | Always | Below 1 Ω |
| Headlight dimmer relay terminal 5 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the DB ECU connector.
Using a service wire, connect DB-16 (DIM) on the wire harness side and body ground.
Check that the headlight high beam illuminates.
Headlight high beam illuminates.
OK
NG