Home › Vehicle Interior › WIPER / WASHER › WIPER SWITCH
RM27M0U _58 Vehicle Interior _049134 WIPER / WASHER _0234268 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT WIPER AND WASHER SWITCH ASSEMBLY

U152764E01
2.364,1.175 2.498,1.316 0.134,0.141 10 A 1.103,1.169 1.237,1.310 0.134,0.141 10 B 1.394,1.291 1.583,1.454 0.189,0.163 10 +1 1.14,2.022 1.414,1.469 false 1.876,1.292 2.114,1.448 0.237,0.156 10 +S 1.004,2.856 1.197,3.003 0.193,0.147 10 +B 1.642,2.871 1.910,3.027 0.267,0.156 10 WF 2.643,1.298 2.928,1.491 0.286,0.193 10 EW 0.34,2.787 0.560,2.962 0.221,0.174 10 +2 0.539,2.709 0.812,2.157 false 1.845,2.842 2.119,2.157 false 1.691,2.022 1.964,1.469 false 2.412,2.022 2.686,1.469 false 1.106,2.88 1.38,2.174 false 0.228,0.263 2.699,0.771 2.471,0.508 10 Component without harness connected: (Front Wiper Switch)

a.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Windshield wiper switch
Tester Connection Switch Condition Specified Condition
B-3 (+1) - B-2 (+B) MIST Below 1 Ω
B-3 (+1) - B-1 (+S) OFF
B-3 (+1) - B-1 (+S) INT
B-3 (+1) - B-2 (+B) LO
B-4 (+2) - B-2 (+B) HI

Windshield washer switch
Tester Connection Switch Condition Specified Condition
A-3 (WF) - A-2 (EW) OFF 10 kΩ or higher
ON Below 1 Ω


If the result is not as specified, replace the switch assembly.


b.
U152765E01
2.364,1.175 2.498,1.316 0.134,0.141 10 A 1.103,1.169 1.237,1.310 0.134,0.141 10 B 1.394,1.291 1.583,1.454 0.189,0.163 10 +1 1.14,2.022 1.414,1.469 false 1.876,1.292 2.114,1.448 0.237,0.156 10 +S 1.004,2.856 1.197,3.003 0.193,0.147 10 +B 1.642,2.871 1.910,3.027 0.267,0.156 10 WF 2.643,1.298 2.928,1.491 0.286,0.193 10 EW 1.845,2.842 2.119,2.157 false 1.691,2.022 1.964,1.469 false 2.412,2.022 2.686,1.469 false 1.106,2.88 1.38,2.174 false 0.228,0.263 2.699,0.771 2.471,0.508 10 Component without harness connected: (Front Wiper Switch)

Check the intermittent operation.

i.

Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).


ii.

Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals A-2 (EW) and B-1 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery's positive (+) lead to terminal B-1 (+S) for 5 seconds.


v.

Connect the battery's negative (-) lead to terminal B-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-3 (+1) and A-2 (EW).

OK:

Refer to illustration below.


E146261E03
0.119,0.829 1.816,0.994 1.698,0.165 10 Voltage between terminals 0.117,1 1.592,1.155 1.475,0.156 10 B-3 (+1) and A-2 (EW) 1.72,0.549 2.439,0.700 0.719,0.151 10 11 to 14 V 2.186,1.028 2.460,1.184 0.274,0.156 10 0 V 2.47,1.463 3.534,1.627 1.064,0.164 10 1.6 +/-1 second 1.881,0 3.870,0.350 1.989,0.350 10 FAST: Connect battery negative lead to terminal B-1 (+S) 4.18,0 6.169,0.351 1.988,0.351 10 SLOW: Connect battery negative lead to terminal B-1 (+S) 4.611,1.454 5.804,1.610 1.193,0.155 10 10.7 +/-5 seconds

If the result is not as specified, replace the switch assembly.



c.
U152766E01
2.364,1.187 2.498,1.328 0.134,0.141 10 A 1.103,1.181 1.237,1.321 0.134,0.141 10 B 1.394,1.303 1.583,1.466 0.189,0.163 10 +1 1.14,2.033 1.414,1.481 false 1.876,1.304 2.114,1.459 0.237,0.156 10 +S 1.004,2.868 1.197,3.014 0.193,0.147 10 +B 2.643,1.309 2.928,1.502 0.286,0.193 10 EW 1.691,2.033 1.964,1.481 false 2.412,2.033 2.686,1.481 false 1.106,2.891 1.38,2.185 false 0.228,0.275 2.699,0.782 2.471,0.508 10 Component without harness connected: (Front Wiper Switch)

Check the washer operation.

i.

Turn the wiper switch OFF.


ii.

Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-1 (+S) and A-2 (EW).


iii.

Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).


iv.

Turn the washer switch ON and OFF, and check the voltage between terminals B-3 (+1) and A-2 (EW).

OK:

Refer to illustration below.


B086335E10
0.281,0.281 0.844,0.604 0.563,0.323 10 false Washer Switch 0.26,0.823 1.979,0.99 1.719,0.167 10 false Voltage between terminals 0.271,0.979 1.729,1.135 1.458,0.156 10 false B-3 (+1) and A-2 (EW) 2.938,0.229 3.177,0.417 0.24,0.188 10 false ON 2.906,0.51 3.229,0.677 0.323,0.167 10 false OFF 2.958,0.969 3.229,1.156 0.271,0.188 10 false 0 V 2.542,0.708 3.219,0.906 0.677,0.198 10 false 11 to 14 V 3.438,1.302 3.969,1.51 0.531,0.208 10 false Approx. 3.406,1.5 4.26,1.698 0.854,0.198 10 false 0.3 seconds 4.531,1.313 5.073,1.5 0.542,0.188 10 false Approx. 4.521,1.51 5.375,1.708 0.854,0.198 10 false 2.2 seconds

If the result is not as specified, replace the switch assembly.