Home › Vehicle Interior › WIPER / WASHER › FRONT WIPER MOTOR
RM27M0U _58 Vehicle Interior _049134 WIPER / WASHER _0234271 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E146306

Install the wiper motor with the 3 bolts.

Torque:
7.5 N*m (75 kgf*cm, 66 in.*lbf)


b.
E344898

Apply MP grease to the crank arm pivot of the wiper motor.


c.

Install the rod of the wiper link to the crank arm, as shown in the illustration.


Hide 2.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

a.
E146300

Install the wiper motor and link assembly with the 4 bolts and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the connector.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E146307

Push the ventilator louver in the direction indicated by the arrow in the illustration to attach 8 claws and 2 clips, and install the ventilator louver.


Hide 53867H 4.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Attach the claw to install the cowl side seal.


Hide 53866J 5.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedures described for the LH side.


Hide 53383 6.INSTALL HOOD TO COWL TOP SEAL

a.
E146298

Attach the 16 claws and install the cowl top seal.


Hide 85221B 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E146308E01
1.544,0.052 2.835,0.216 1.291,0.164 10 Wiper Arm Serration 2.511,1.912 3.249,2.076 0.738,0.164 10 Wire Brush 2.474,1.996 2.199,1.996 false 2.199,1.991 2.199,2.42 false 3.127,0.157 3.333,0.157 false 3.333,0.151 3.333,1.681 false 3.339,1.681 1.935,1.681 false 0.151,4.196 1.501,4.361 1.350,0.165 10 Wiper Pivot Serration 1.222,3.509 0.99,4.127 false

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration with a wire brush.


d.
E146317E01
2.928,1.186 3.205,1.405 0.277,0.219 10 A 0.946,1.191 1.223,1.411 0.277,0.219 10 B 1.567,0.696 2.525,0.933 0.959,0.237 10 Louver Edge 1.48,0.788 1.099,0.788 1.099,0.788 0.478,1.561 false

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Standard measurement:
Position Specified Condition
A 23.9 mm (0.941 in.)
B 35.5 mm (1.40 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



Hide 85211B 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E146308E01
1.544,0.052 2.835,0.216 1.291,0.164 10 Wiper Arm Serration 2.511,1.912 3.249,2.076 0.738,0.164 10 Wire Brush 2.474,1.996 2.199,1.996 false 2.199,1.991 2.199,2.42 false 3.127,0.157 3.333,0.157 false 3.333,0.151 3.333,1.681 false 3.339,1.681 1.935,1.681 false 0.151,4.196 1.501,4.361 1.350,0.165 10 Wiper Pivot Serration 1.222,3.509 0.99,4.127 false

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration with a wire brush.


d.
E146310E01
1.711,1.217 1.866,1.429 0.154,0.212 10 A 0.061,1.058 0.216,1.270 0.154,0.212 10 B 1.026,0.69 1.982,1.022 0.956,0.332 10 Louver Edge 2.09,0.806 2.391,0.806 2.391,0.806 2.95,1.552 false

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Standard measurement:
Position Specified Condition
A 11.5 mm (0.453 in.)
B 29.8 mm (1.17 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



e.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.