Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049135 AUDIO / VIDEO _0234292 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Stereo Component Amplifier Power Source Circuit  


DESCRIPTION

This circuit provides power to the stereo component amplifier assembly.

WIRING DIAGRAM

E286743E02
5.188,2.083 5.563,2.229 0.375,0.146 10 false GND 5.198,0.542 5.625,0.771 0.427,0.229 10 false +B 5,0.438 5.188,0.583 0.188,0.146 10 false 1 5,1.469 5.188,1.615 0.188,0.146 10 false 9 4.948,2.531 5.313,2.708 0.365,0.177 10 false J144 5,1.958 5.177,2.177 0.177,0.219 10 false 7 4.063,0.708 4.406,0.917 0.344,0.208 10 false AMP 4.948,2.719 6.219,3.125 1.271,0.406 10 false Stereo Component Amplifier Assembly 2.469,0.542 3.281,0.792 0.813,0.25 10 false from Battery 5.198,1.052 5.604,1.24 0.406,0.188 10 false ACC 5,0.948 5.188,1.094 0.188,0.146 10 false 3 4.073,1.208 4.417,1.417 0.344,0.208 10 false ACC 2.24,1.031 3.271,1.302 1.031,0.271 10 false from ACC Relay 5.188,1.552 5.625,1.74 0.438,0.188 10 false AMP 1.479,1.573 1.917,1.76 0.438,0.188 10 false AMP 1.896,1.448 2.333,1.635 0.438,0.188 10 false 9 0.813,1.938 1.208,2.125 0.396,0.188 10 false J137 0.802,2.115 2.073,2.552 1.271,0.438 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U152908E02
2.26,1.073 2.49,0.823 2.49,0.823 2.688,0.823 true 2.031,1.073 2.25,0.51 2.25,0.51 2.448,0.51 true 1.635,1.427 1.823,1.833 1.823,1.833 2.021,1.833 true 0.104,0.073 0.438,0.26 0.333,0.188 10 false *a 2.74,0.74 3.115,0.927 0.375,0.188 10 false +B 2.073,1.75 2.771,1.938 0.698,0.188 10 false GND 1.604,0.365 1.938,0.552 0.333,0.188 10 false J144 2.51,0.438 2.885,0.625 0.375,0.188 10 false ACC

Disconnect the stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J144-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J144-4 (+B) - Body ground Always 11 to 14 V
J144-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the J144 stereo component amplifier assembly connector.


b.

Disconnect the J137 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J144-9 (AMP) - J137-9 (AMP) Always Below 1 Ω
J144-9 (AMP) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR