Wear protective gloves. Sharp areas on the parts may injure your hands.
73160A
1.INSTALL CENTER FRONT SEAT BELT ASSEMBLY
Attach the 2 claws to install the center front seat belt assembly.
Install the bolt and nut.
71875L
2.INSTALL CENTER SEAT RECLINING ADJUSTER INSIDE COVER RH
Attach the claw to install the center seat reclining adjuster inside cover RH.
71876L
3.INSTALL CENTER SEAT RECLINING ADJUSTER INSIDE COVER LH
Attach the claw to install the center seat reclining adjuster inside cover LH.
71365S
4.INSTALL CENTER SEATBACK PAD
Install the center seatback pad.
71035S
5.INSTALL CENTER FRONT SEATBACK COVER
Install the center front seatback cover.
71931
6.INSTALL FRONT SEAT HEADREST SUPPORT
Attach the 4 claws to install the 2 front seat headrest supports.
71705E
7.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY
RH Side:
Connect the cable to the center seatback frame inner side.
LH Side:
Connect the cable to the center seatback frame inner side.
Attach the 21 claws to install the front seatback board sub-assembly.
Install the screw.
Install the 6 screws.
71738
8.INSTALL SEAT FASTENER COVER
Attach the 6 claws to install the 2 seat fastener covers.
72982
9.INSTALL CENTER FRONT SEAT ARMREST COVER
Install the center front seat armrest cover with the 2 screws.
71753B
10.INSTALL FRONT SEAT TRAY
Attach the 5 clips to install the front seat tray.
72597
11.INSTALL RECLINING REMOTE CONTROL BEZEL
Attach the 2 clips and claw to install the reclining control bezel.
73373J
12.INSTALL LOWER FRONT SEAT SHOULDER BELT COVER
Using a T30 "TORX" socket wrench, install the lower front seat shoulder belt cover with the 2 bolts.
72667
13.INSTALL UPPER REAR SEATBACK LOCK BEZEL
Connect the center front seat belt assembly to the front seat shoulder belt cover.
Attach the 4 claws to install the upper rear seatback lock bezel.
73373J
14.INSTALL FRONT SEAT SHOULDER BELT COVER
Using a T10 "TORX" socket wrench, install the front seat shoulder belt cover with the 2 screws.
71910A
15.INSTALL FRONT SEAT HEADREST ASSEMBLY
Install the front seat headrest assembly.
82166
16.INSTALL CONSOLE BOX WIRE
Attach the 4 clamps to install the console box wire.
85535F
17.INSTALL CENTER POWER OUTLET SOCKET COVER
85530B
18.INSTALL POWER OUTLET SOCKET ASSEMBLY
71753
19.INSTALL FRONT SEAT UNDER TRAY
Using a T30 "TORX" socket wrench, install the front seat under tray with the 2 bolts.
Connect the connector of the power outlet socket assembly.
78849
20.INSTALL FOLD SEAT STOPPER CUSHION
Using a T20 "TORX" socket wrench, install the 2 fold stopper cushions with the 2 screws.
21.INSTALL CENTER SEATBACK ASSEMBLY
Install the center seatback assembly.
RH Side:
Using a T55 "TORX" socket wrench, install the 2 bolts.
LH Side:
Using a T40 "TORX" socket wrench, install the 2 bolts.
Install the 2 wire harness clamps to the center seatback frame.
73160A
22.CONNECT CENTER FRONT SEAT BELT ASSEMBLY RH
Connect the center front seat belt assembly RH with the bolt.
73240A
23.INSTALL CENTER FRONT SEAT INNER BELT ASSEMBLY
Install the center front seat inner belt assembly with the bolt.
Do not allow the anchor of the center front seat inner belt assembly to overlap the protruding part of the center seatback frame.
| *1 | Protruding Part |
71511C
24.INSTALL CENTER FRONT SEAT CUSHION PAD
Using hog ring pliers, install the seat cushion pad to the seat cushion frame with new hog rings.
Using hog ring pliers, install the center front seat cushion pad to the center seat cushion frame with 3 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
| *1 | Hog Ring Pliers |
72696
25.INSTALL REAR SEAT LOCK LATCH
Install the rear seat lock latch and fasten the button.
Using a T30 "TORX" socket wrench, install the 2 bolts.
26.INSTALL CENTER FRONT SEAT CUSHION ASSEMBLY
Install the center front seat cushion assembly with the 2 bolts.
71071C
27.INSTALL CENTER FRONT SEAT CUSHION COVER
Install the center front seat cushion cover, and then attach the 3 hooks.
71811Q
28.INSTALL CENTER SEAT CUSHION SHIELD RH
Attach the 7 claws and 3 clips to install the center seat cushion shield RH.
Using a T30 "TORX" socket wrench, install the bolt.
71812R
29.INSTALL CENTER SEAT CUSHION SHIELD LH
Attach the 7 claws and 2 clips to install the center seat cushion shield LH.
Using a T30 "TORX" socket wrench, install the bolt.
85535E
30.INSTALL REAR POWER OUTLET SOCKET COVER (for CrewMax)
85530D
31.INSTALL REAR POWER OUTLET SOCKET (for CrewMax)
72679A
32.INSTALL NO. 2 SEATBACK LOCK CONTROL BEZEL (for CrewMax)
Install the No. 2 seatback lock control bezel with the 4 screws.
58860B
33.INSTALL NO. 1 CONSOLE BOX REGISTER ASSEMBLY (for CrewMax)
Install the No. 1 console box register assembly with the 3 screws.
58860C
34.INSTALL NO. 2 CONSOLE BOX REGISTER ASSEMBLY (for CrewMax)
Install the No. 2 console box register assembly with the 3 screws.
85535B
35.INSTALL REAR POWER OUTLET SOCKET COVER (for Double Cab)
85530
36.INSTALL REAR POWER OUTLET SOCKET ASSEMBLY (for Double Cab)
71353
37.INSTALL CENTER SEATBACK PANEL
for Regular Cab:
Attach the 4 claws and 4 clips to install the center seatback panel.
for Double Cab:
Connect the connector.
Attach the 4 clips to install the center seatback panel.
Install the 2 screws.
for CrewMax:
Connect the connector.
Attach the 4 claws and 4 clips to install the center seatback panel.