Wear protective gloves. Sharp areas on the parts may injure your hands.
1.REMOVE REAR SEAT ASSEMBLY LH
Using a T50 "TORX" socket wrench, remove the 2 bolts and rear seat assembly LH.
79106
2.REMOVE NO. 1 SEAT LEG SUB-ASSEMBLY LH
Using a T40 "TORX" socket wrench, remove the bolt.
Remove the bolt and No. 1 seat leg sub-assembly LH.
79105
3.REMOVE NO. 1 SEAT LEG SUB-ASSEMBLY RH
Remove the bolt and No. 1 seat leg sub-assembly RH.
72666E
4.REMOVE OUTER REAR SEAT LOCK COVER LH
Remove the screw.
Detach the clip and 2 claws labeled A, and then detach the claw labeled B in the direction indicated by the arrow in the illustration and remove the outer rear seat lock cover LH.
72665G
5.REMOVE INNER REAR SEAT LOCK COVER LH
Remove the 2 screws.
Detach the 2 claws labeled A, and then detach the claw labeled B in the direction indicated by the arrow in the illustration and remove the inner rear seat lock cover LH.
6.REMOVE REAR SEAT CUSHION ASSEMBLY LH
Using a T40 "TORX" socket wrench, remove the 2 bolts and rear seat cushion assembly LH.
72679
7.REMOVE REAR SEATBACK LOCK CONTROL BEZEL LH
Detach the 4 claws and remove the rear seatback lock control bezel LH.
8.REMOVE REAR SEAT CUSHION COVER WITH PAD LH
Disconnect the cable from the rear seat turn lock sub-assembly LH.
Detach the hook and open the 2 fasteners, and then open the separate type rear seat cushion cover LH.
| *1 | Fastener |
Detach each hook from the rear seat cushion frame sub-assembly LH.
Detach the 2 hooks from the rear seat cushion frame sub-assembly LH.
Remove the 5 hog rings and rear seat cushion cover with pad LH.
71076S
9.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH
Remove the 9 hog rings and separate type rear seat cushion cover LH from the separate type rear seat cushion pad LH.
72526B
10.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH
Cut the cable tie and disconnect the cable.
| *1 | Cable Tie |
Remove the 4 screws and No. 1 reclining adjuster release handle LH.
71486C
11.REMOVE REAR SEAT HINGE COVER LH
Remove the 2 screws and rear seat hinge cover LH.
71485C
12.REMOVE REAR SEAT HINGE COVER RH
Remove the 2 screws and rear seat hinge cover RH.
72094
13.REMOVE REAR SEAT TURN LOCK SUB-ASSEMBLY LH
Remove the bolt and rear seat turn lock sub-assembly LH.
71940A
14.REMOVE REAR SEAT HEADREST ASSEMBLY LH
Remove the rear seat headrest assembly LH.
71960B
15.REMOVE CENTER REAR SEAT HEADREST ASSEMBLY
Remove the center rear seat headrest assembly.
71931A
16.REMOVE REAR SEAT HEADREST SUPPORT LH
Detach the 4 claws and remove the 2 rear seat headrest supports.
71931B
17.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
18.REMOVE REAR SEATBACK COVER WITH PAD LH
Detach the 6 hooks and remove the rear seatback cover with pad LH.
71078S
19.REMOVE SEPARATE TYPE REAR SEATBACK COVER LH
Remove the 9 hog rings and separate type rear seatback cover LH from the separate type rear seatback pad LH.
79106A
20.REMOVE SEAT LEG SUB-ASSEMBLY LH
Remove the bolt and seat leg sub-assembly LH.
79105A
21.REMOVE NO. 1 SEAT LEG SUB-ASSEMBLY
Using a T45 "TORX" socket wrench, remove the bolt.
Remove the bolt and No. 1 seat leg sub-assembly.
72666D
22.REMOVE INNER REAR SEAT LOCK COVER RH
Remove the 2 screws.
Detach the 2 claws labeled A, and then detach the claw labeled B in the direction indicated by the arrow in the illustration and remove the inner rear seat lock cover RH.
72665F
23.REMOVE OUTER REAR SEAT LOCK COVER RH
Remove the screw.
Detach the clip and 2 claws labeled A, and then detach the claw labeled B in the direction indicated by the arrow in the illustration and remove the outer rear seat lock cover RH.
24.REMOVE REAR SEAT CUSHION ASSEMBLY RH
Using a T40 "TORX" socket wrench, remove the 2 bolts and rear seat cushion assembly RH.
72679
25.REMOVE REAR SEATBACK LOCK CONTROL BEZEL RH
Detach the 4 claws and remove the rear seatback lock control bezel RH.
26.REMOVE REAR SEAT CUSHION COVER WITH PAD RH
Disconnect the cable from the rear seat turn lock sub-assembly RH.
Detach the hook and open the 2 fasteners, and then open the separate type rear seat cushion cover RH.
| *1 | Fastener |
Detach the 5 hooks from the rear seat cushion frame sub-assembly RH.
Detach the 2 hooks and remove the 2 hog rings, and then remove the rear seat cushion cover with pad RH.
71075S
27.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH
Remove the 9 hog rings and separate type rear seat cushion cover RH from the separate type rear seat cushion pad RH.
72525C
28.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Cut the cable tie and disconnect the cable.
| *1 | Cable Tie |
Remove the 4 screws and No. 1 reclining adjuster release handle RH.
71486C
29.REMOVE REAR SEAT HINGE COVER LH
Remove the 2 screws and rear seat hinge cover LH.
71485C
30.REMOVE REAR SEAT HINGE COVER RH
Remove the 2 screws and rear seat hinge cover RH.
72094
31.REMOVE REAR SEAT TURN LOCK SUB-ASSEMBLY RH
Remove the bolt and rear seat turn lock sub-assembly RH.
71940A
32.REMOVE REAR SEAT HEADREST ASSEMBLY RH
Remove the rear seat headrest assembly RH.
71931A
33.REMOVE REAR SEAT HEADREST SUPPORT RH
Detach the 4 claws and remove the 2 rear seat headrest supports.
34.REMOVE REAR SEATBACK COVER WITH PAD RH
Detach the 4 hooks and remove the rear seatback cover with pad RH.
71077S
35.REMOVE SEPARATE TYPE REAR SEATBACK COVER RH
Remove the 9 hog rings and separate type rear seatback cover RH from the separate type rear seatback pad RH.