Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for Double Cab)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234297 REAR SEAT ASSEMBLY(for Double Cab) A

SEAT  REAR SEAT ASSEMBLY(for Double Cab)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71077S 1.INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

a.

Set the separate type rear seatback cover RH in place.


b.
B356753E01
0.675,1.693 0.863,1.872 0.188,0.179 10 *1 0.578,1.223 0.766,1.402 0.188,0.179 10 *a 1.185,0.713 0.715,1.24 false 1.219,1.761 0.853,1.761 false

Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 9 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


Hide 2.INSTALL REAR SEATBACK COVER WITH PAD RH

B356751

a.

Install the rear seatback cover with pad RH to the rear seatback frame sub-assembly RH, and then attach the 4 hooks.


Hide 71931A 3.INSTALL REAR SEAT HEADREST SUPPORT RH

a.

Attach 4 claws to install the 2 rear seat headrest supports.


Hide 71940A 4.INSTALL REAR SEAT HEADREST ASSEMBLY RH

a.

Install the rear seat headrest assembly RH.


Hide 72094 5.INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY RH

B166339

a.

Install the rear seat turn lock sub-assembly RH with the bolt.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 71485C 6.INSTALL REAR SEAT HINGE COVER RH

B165767

a.

Install the rear seat hinge cover RH with the 2 screws.


Hide 71486C 7.INSTALL REAR SEAT HINGE COVER LH

a.

Install the rear seat hinge cover LH with the 2 screws.


Hide 72525C 8.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH

B165778E03
2.417,0.176 2.597,0.349 0.180,0.173 10 *1 1.69,1.147 2.163,0.271 2.163,0.271 2.387,0.271 false

a.

Install the No. 1 reclining adjuster release handle RH with the 4 screws.


b.

Connect the cable and install a new cable tie.

Text in Illustration
*1 Cable Tie


c.
B272385E01
2.195,2.233 2.349,2.414 0.154,0.181 10 *b 0.981,3.981 1.129,4.163 0.148,0.181 10 *c 2.244,3.981 2.402,4.163 0.157,0.181 10 *d 2.288,1.307 2.444,1.463 0.156,0.156 10 *a

Cut off the end of the cable tie as shown in the illustration.

Text in Illustration
*a Cut Here
*b 10 mm (0.40 in.)
*c Correct
*d Incorrect


Hide 71075S 9.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH

a.

Set the separate type rear seat cushion cover RH in place.


b.
B356754E01
0.675,1.693 0.863,1.872 0.188,0.179 10 *1 0.578,1.223 0.766,1.402 0.188,0.179 10 *a 1.185,0.713 0.715,1.24 false 1.219,1.761 0.853,1.761 false

Using hog ring pliers, install the separate type rear seat cushion cover RH to the separate type rear seat cushion pad RH with 9 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


Hide 10.INSTALL REAR SEAT CUSHION COVER WITH PAD RH

a.
B356749

Using hog ring pliers, install the rear seat cushion cover with pad RH to the rear seat cushion frame sub-assembly RH with 2 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


b.

Attach the 2 hooks.


c.
B356748

Attach the 5 hooks to the seat cushion frame sub-assembly RH.


d.
B356747E01
0.406,0.073 0.599,0.243 0.193,0.170 10 *1 2.843,1.368 3.036,1.538 0.193,0.170 10 *1 0.941,0.54 0.598,0.202 false 2.568,1.09 2.878,1.365 false

Fold down the separate type rear seat cushion cover RH and close the 2 fasteners, and then attach the hook.

Text in Illustration
*1 Fastener


e.
B166342

Connect the cable to the rear seat turn lock sub-assembly RH.


Hide 72679 11.INSTALL REAR SEATBACK LOCK CONTROL BEZEL RH

B166337

a.

Attach the 4 claws to install the rear seatback lock control bezel RH.


Hide 12.INSTALL REAR SEAT CUSHION ASSEMBLY RH

B165773

a.

Using a T40 "TORX" socket wrench, install the rear seat cushion assembly RH with the 2 bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 72665F 13.INSTALL OUTER REAR SEAT LOCK COVER RH

B166340E03
2.96,0.251 3.099,0.407 0.139,0.156 10 A 1.998,1.54 2.136,1.696 0.139,0.156 10 B 2.292,0.758 2.924,0.38 2.924,0.38 2.335,0.942 false 2.378,1.295 2.133,1.574 false

a.

Attach the claw labeled B in the direction indicated by the arrow in the illustration, and then attach the clip and 2 claws labeled A to install the outer rear seat lock cover RH.


b.

Install the screw.


Hide 72666D 14.INSTALL INNER REAR SEAT LOCK COVER RH

B166341E02
1.258,0.175 1.409,0.335 0.151,0.161 10 A 1.806,1.818 1.958,1.978 0.151,0.161 10 B 1.62,1.608 1.781,1.838 false 1.888,0.881 1.411,0.309 1.411,0.309 1.918,0.666 false

a.

Attach the claw labeled B in the direction indicated by the arrow in the illustration, and then attach the 2 claws labeled A to install the inner rear seat lock cover RH.


b.

Install the 2 screws.


Hide 79105A 15.INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY

B166554

a.

Install the No. 1 seat leg sub-assembly with the bolt.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


b.

Using a T45 "TORX" socket wrench, install the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 79106A 16.INSTALL SEAT LEG SUB-ASSEMBLY LH

B166346

a.

Install the seat leg sub-assembly LH with the bolt.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


Hide 71078S 17.INSTALL SEPARATE TYPE REAR SEATBACK COVER LH

a.

Set the separate type rear seatback cover LH in place.


b.
B356755E01
0.675,1.693 0.863,1.872 0.188,0.179 10 *1 0.578,1.223 0.766,1.402 0.188,0.179 10 *a 1.185,0.713 0.715,1.24 false 1.219,1.761 0.853,1.761 false

Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 9 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


Hide 18.INSTALL REAR SEATBACK COVER WITH PAD LH

B356745

a.

Install the rear seatback cover with pad to the rear seatback frame sub-assembly LH, and then attach the 6 hooks.


Hide 71931B 19.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


Hide 71931A 20.INSTALL REAR SEAT HEADREST SUPPORT LH

a.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 71960B 21.INSTALL CENTER REAR SEAT HEADREST ASSEMBLY

a.

Install the center rear seat headrest assembly.


Hide 71940A 22.INSTALL REAR SEAT HEADREST ASSEMBLY LH

a.

Install the rear seat headrest assembly LH.


Hide 72094 23.INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY LH

B165768

a.

Install the rear seat turn lock sub-assembly LH with the bolt.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 71485C 24.INSTALL REAR SEAT HINGE COVER RH

B165767

a.

Install the rear seat hinge cover RH with the 2 screws.


Hide 71486C 25.INSTALL REAR SEAT HINGE COVER LH

a.

Install the rear seat hinge cover LH with the 2 screws.


Hide 72526B 26.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH

a.
B165764E03
2.672,0.198 2.890,0.363 0.218,0.165 10 *1 2.018,1.197 2.52,0.289 2.52,0.289 2.663,0.289 false

Install the No. 1 reclining adjuster release handle LH with the 4 screws.


b.

Connect the cable and install a new cable tie.

Text in Illustration
*1 Cable Tie


c.
B272385E01
2.195,2.233 2.349,2.414 0.154,0.181 10 *b 0.981,3.981 1.129,4.163 0.148,0.181 10 *c 2.244,3.981 2.402,4.163 0.157,0.181 10 *d 2.288,1.307 2.444,1.463 0.156,0.156 10 *a

Cut off the end of the cable tie as shown in the illustration.

Text in Illustration
*a Cut Here
*b 10 mm (0.40 in.)
*c Correct
*d Incorrect


Hide 71076S 27.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH

a.

Set the separate type rear seat cushion cover LH in place.


b.
B356756E01
0.675,1.693 0.863,1.872 0.188,0.179 10 *1 0.578,1.223 0.766,1.402 0.188,0.179 10 *a 1.185,0.713 0.715,1.24 false 1.219,1.761 0.853,1.761 false

Using hog ring pliers, install the separate type rear seat cushion cover LH to the separate type rear seat cushion pad LH with 9 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover LH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


Hide 28.INSTALL REAR SEAT CUSHION COVER WITH PAD LH

a.
B356757E01
0.663,1.748 0.852,1.927 0.188,0.179 10 *1 0.382,1.324 0.571,1.503 0.188,0.179 10 *a 1.202,1.006 0.583,1.385 false 1.207,1.817 0.841,1.817 false

Using hog ring pliers, install the rear seat cushion cover with pad LH to the rear seat cushion frame sub-assembly LH with 5 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover LH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


b.
B356742

Attach the 2 hooks to the seat cushion frame sub-assembly LH.


c.
B356741

Attach each hook to the seat cushion frame sub-assembly LH.


d.
B356740E02
0.531,1.302 0.313,1.542 false 2.906,1.302 3.031,1.521 false 0.146,1.573 0.323,1.729 0.177,0.156 10 false *1 3.042,1.552 3.219,1.708 0.177,0.156 10 false *1

Fold down the separate type rear seat cushion cover LH and close the 2 fasteners, and then attach the hook.

Text in Illustration
*1 Fastener


e.
B166345

Connect the cable to the rear seat turn lock sub-assembly LH.


Hide 72679 29.INSTALL REAR SEATBACK LOCK CONTROL BEZEL LH

B165608

a.

Attach the 4 claws to install the rear seatback lock control bezel LH.


Hide 30.INSTALL REAR SEAT CUSHION ASSEMBLY LH

B165607

a.

Using a T40 "TORX" socket wrench, install the rear seat cushion assembly LH with the 2 bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 72665G 31.INSTALL INNER REAR SEAT LOCK COVER LH

B166344E02
1.958,0.165 2.096,0.334 0.137,0.170 10 A 2.153,1.783 2.290,1.953 0.137,0.170 10 B 1.557,0.686 1.918,0.314 1.918,0.314 1.563,0.898 false 1.953,1.597 2.13,1.803 false

a.

Attach the claw labeled B in the direction indicated by the arrow in the illustration, and then attach the 2 claws labeled A to install the inner rear seat lock cover LH.


b.

Install the 2 screws.


Hide 72666E 32.INSTALL OUTER REAR SEAT LOCK COVER LH

B166343E03
0.389,0.256 0.544,0.431 0.156,0.174 10 A 1.322,1.488 1.478,1.663 0.156,0.174 10 B 1.116,0.892 0.549,0.4 0.549,0.4 1.162,0.726 false 1.087,1.265 1.294,1.528 false

a.

Attach the claw labeled B in the direction indicated by the arrow in the illustration, and then attach the clip and 2 claws labeled A to install the outer rear seat lock cover LH.


b.

Install the screw.


Hide 79105 33.INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY RH

B165604

a.

Install the No. 1 seat leg sub-assembly RH with the bolt.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


Hide 79106 34.INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY LH

B165603

a.

Install the No. 1 seat leg sub-assembly LH with the bolt.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


b.

Using a T45 "TORX" socket wrench, install the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 35.INSTALL REAR SEAT ASSEMBLY LH

B165602

a.

Using a T50 "TORX" socket wrench, install the rear seat assembly LH with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)