84922C
1.INSPECT FRONT POWER SEAT SWITCH LH
Check the resistance of the front power seat switch LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (SLDF) - 8 (B)
5 (SLDF) - 7 (B1) |
Front position | Below 1 Ω |
| 2 (SLDR) - 11 (E)
2 (SLDR) - 12 (E1) |
||
| 5 (SLDF) - 11 (E)
5 (SLDF) - 12 (E1) |
Neutral | |
| 2 (SLDR) - 11 (E)
2 (SLDR) - 12 (E1) |
||
| 5 (SLDF) - 11 (E)
5 (SLDF) - 12 (E1) |
Rear position | |
| 2 (SLDR) - 8 (B)
2 (SLDR) - 7 (B1) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (FUP) - 8 (B)
1 (FUP) - 7 (B1) |
Up position | Below 1 Ω |
| 6 (FDWN) - 11 (E)
6 (FDWN) - 12 (E1) |
||
| 1 (FUP) - 11 (E)
1 (FUP) - 12 (E1) |
Neutral | |
| 6 (FDWN) - 11 (E)
6 (FDWN) - 12 (E1) |
||
| 1 (FUP) - 11 (E)
1 (FUP) - 12 (E1) |
Down position | |
| 6 (FDWN) - 8 (B)
6 (FDWN) - 7 (B1) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (LUP) - 8 (B)
3 (LUP) - 7 (B1) |
Up position | Below 1 Ω |
| 4 (LDWN) - 11 (E)
4 (LDWN) - 12 (E1) |
||
| 3 (LUP) - 11 (E)
3 (LUP) - 12 (E1) |
Neutral | |
| 4 (LDWN) - 11 (E)
4 (LDWN) - 12 (E1) |
||
| 3 (LUP) - 11 (E)
3 (LUP) - 12 (E1) |
Down position | |
| 4 (LDWN) - 8 (B)
4 (LDWN) - 7 (B1) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 8 (B) - 10 (RCLF)
7 (B1) - 10 (RCLF) |
Front position | Below 1 Ω |
| 9 (RCLR) - 11 (E)
9 (RCLR) - 12 (E1) |
||
| 10 (RCLF) - 11 (E)
10 (RCLF) - 12 (E1) |
Neutral | |
| 9 (RCLR) - 11 (E)
9 (RCLR) - 12 (E1) |
||
| 10 (RCLF) - 11 (E)
10 (RCLF) - 12 (E1) |
Rear position | |
| 8 (B) - 9 (RCLR)
7 (B1) - 9 (RCLR) |
If the result is not as specified, replace the front power seat switch LH.
| *1 | Front Vertical Switch |
| *2 | Slide Switch |
| *3 | Lifter Switch |
| *4 | Reclining Switch |
| *a | Component without harness connected
(Front Power Seat Switch LH) |
84922B
2.INSPECT FRONT POWER SEAT SWITCH RH
Check the resistance of the front power seat switch RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (SLDF) - 13 (B)
2 (SLDF) - 14 (B1) |
Front position | Below 1 Ω |
| 5 (SLDR) - 10 (E)
5 (SLDR) - 9 (E1) |
||
| 2 (SLDF) - 10 (E)
2 (SLDF) - 9 (E1) |
Neutral | |
| 5 (SLDR) - 10 (E)
5 (SLDR) - 9 (E1) |
||
| 2 (SLDF) - 10 (E)
2 (SLDF) - 9 (E1) |
Rear position | |
| 5 (SLDR) - 13 (B)
5 (SLDR) - 14 (B1) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 11 (RCLF) - 13 (B)
11 (RCLF) - 14 (B1) |
Front position | Below 1 Ω |
| 10 (E) - 12 (RCLR)
9 (E1) - 12 (RCLR) |
||
| 10 (E) - 11 (RCLF)
9 (E1) - 11 (RCLF) |
Neutral | |
| 12 (RCLR) - 10 (E)
12 (RCLR) - 9 (E1) |
||
| 10 (E) - 11 (RCLF)
9 (E1) - 11 (RCLF) |
Rear position | |
| 12 (RCLR) - 13 (B)
12 (RCLR) - 14 (B1) |
If the result is not as specified, replace the front power seat switch.
| *1 | Slide Switch |
| *2 | Reclining Switch |
| *a | Component without harness connected
(Front Power Seat Switch RH) |