Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code DTC Detection Condition Trouble Area
B2658 A problem with the voltage supplied to the position control sensor.
·

Position control ECU and switch assembly

·

Front seat cushion frame sub-assembly LH

·

Front seatback frame sub-assembly LH

·

Harness or connector



WIRING DIAGRAM

B352950E01
5.097,0.636 5.894,0.889 0.796,0.253 10 SSRS 4.888,0.546 5.059,0.730 0.171,0.185 10 5 5.097,1.044 5.894,1.297 0.796,0.253 10 SGND 4.888,0.954 5.059,1.139 0.171,0.185 10 1 3.121,0.546 3.292,0.730 0.171,0.185 10 5 3.121,0.958 3.292,1.143 0.171,0.185 10 6 0.711,0.584 0.995,0.768 0.284,0.185 10 Z3 0.711,0.735 2.466,1.049 1.755,0.314 10 Front Power Seat Position Motor LH (Slide Motor) 5.097,1.73 5.894,1.983 0.796,0.253 10 SSRL 4.888,1.64 5.059,1.824 0.171,0.185 10 4 3.121,1.64 3.292,1.824 0.171,0.185 10 4 3.121,2.052 3.292,2.237 0.171,0.185 10 3 3.121,5.015 3.292,5.200 0.171,0.185 10 4 3.121,5.428 3.292,5.612 0.171,0.185 10 3 0.711,1.671 0.995,1.855 0.284,0.185 10 Z4 0.711,1.834 2.364,2.148 1.653,0.314 10 Front Power Seat Position Motor LH (Lifter Motor) 0.628,3.665 3.474,3.862 2.845,0.197 10 Front Seat Cushion Frame Sub-assembly LH 5.097,5.106 5.894,5.359 0.796,0.253 10 SSRR 4.82,5.016 5.059,5.201 0.238,0.185 10 11 0.711,5.016 0.995,5.201 0.284,0.185 10 Z6 0.711,2.752 0.995,2.937 0.284,0.185 10 Z14 0.711,5.167 2.405,5.481 1.694,0.314 10 Front Power Seat Position Motor LH (Reclining Motor) 0.66,5.978 3.304,6.175 2.644,0.197 10 Front Seatback Frame Sub-assembly LH 5.097,2.826 5.894,3.078 0.796,0.253 10 SSFV 4.888,2.735 5.126,2.920 0.238,0.185 10 3 3.121,2.735 3.292,2.920 0.171,0.185 10 2 3.121,3.148 3.292,3.332 0.171,0.185 10 1 0.711,2.903 2.405,3.217 1.694,0.314 10 Front Power Seat Position Motor LH (Vertical Motor) 4.831,5.566 5.240,5.763 0.408,0.197 10 Z10 4.831,5.762 6.451,6.127 1.619,0.365 10 Position Control ECU and Switch Assembly

PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Disconnect the Z3 front seat cushion frame sub-assembly LH (slide motor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-5 (SSRS) - Z3-5 Always Below 1 Ω
Z10-1 (SGND) - Z3-6 Always Below 1 Ω
Z10-5 (SSRS) - Z10-1 (SGND) Always 10 kΩ or higher
Z10-5 (SSRS) or Z3-5 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z3-6 - Body ground Always 10 kΩ or higher




OK

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
a.
U152016E02
0.76,1.052 0.969,1.229 0.208,0.177 10 false Z3 0.115,0.115 0.323,0.292 0.208,0.177 10 false *a

Reconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z3-5 - Z3-6 Sliding switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Slide Motor])



OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Disconnect the Z4 front seat cushion frame sub-assembly LH (lifter motor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-4 (SSRL) - Z4-4 Always Below 1 Ω
Z10-1 (SGND) - Z4-3 Always Below 1 Ω
Z10-4 (SSRL) - Z10-1 (SGND) Always 10 kΩ or higher
Z10-4 (SSRL) or Z4-4 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z4-3 - Body ground Always 10 kΩ or higher




OK

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.
U152031E02
0.052,0 0.26,0.208 0.208,0.208 10 false *a 0.375,0.958 0.573,1.156 0.198,0.198 10 false Z4

Reconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z4-4 - Z4-3 Lifter switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Lifter Motor])



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Disconnect the Z14 front seat cushion frame sub-assembly LH (vertical motor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-3 (SSFV) - Z14-2 Always Below 1 Ω
Z10-1 (SGND) - Z14-1 Always Below 1 Ω
Z10-3 (SSFV) - Z10-1 (SGND) Always 10 kΩ or higher
Z10-3 (SSFV) or Z14-2 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z14-1 - Body ground Always 10 kΩ or higher




OK

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (VERTICAL MOTOR CIRCUIT)
a.
U152035E02
0.688,0.865 0.979,1.042 0.292,0.177 10 false Z14 0.125,0.125 0.333,0.302 0.208,0.177 10 false *a

Reconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z14-2 - Z14-1 Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Vertical Motor])



OK

8.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

8.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH
a.

Temporarily replace the front seat cushion frame sub-assembly LH with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH WAS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Disconnect the Z6 front seatback frame sub-assembly LH (reclining motor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-11 (SSRR) - Z6-4 Always Below 1 Ω
Z10-1 (SGND) - Z6-3 Always Below 1 Ω
Z10-11 (SSRR) - Z10-1 (SGND) Always 10 kΩ or higher
Z10-11 (SSRR) or Z6-4 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z6-3 - Body ground Always 10 kΩ or higher




OK

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.
U152032E02
0.052,0 0.26,0.208 0.208,0.208 10 false *a 0.365,0.958 0.573,1.146 0.208,0.188 10 false Z6

Reconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z6-4 - Z6-3 Reclining switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seatback Frame Sub-assembly LH [Reclining Motor])



OK

11.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

11.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH
a.

Temporarily replace the front seatback frame sub-assembly LH (reclining motor) with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (FRONT SEATBACK FRAME SUB-ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY