Wear protective gloves. Sharp areas on the parts may injure your hands.
71940A
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Push the 2 lock release buttons indicated by the arrows in the illustration to release the lock, and then remove the rear seat headrest assembly.
71960B
2.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
Push the lock release button indicated by the arrows in the illustration to release the lock, and then remove the rear center seat headrest assembly.
72679
3.REMOVE REAR SEATBACK LOCK CONTROL BEZEL
Pull out the 2 fasteners.
Detach the 2 hooks and open the 2 fasteners, and then open the separate type rear seat cushion cover.
Detach the 4 claws on the backside of the rear seatback lock control bezel and remove the rear seatback lock control bezel.
4.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Detach the 6 hooks and remove the separate type rear seat cushion cover with pad.
71076S
5.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 12 hog rings and detach the 2 fasteners to remove the separate type rear seat cushion cover.
| *1 | Fastener |
71834D
6.REMOVE REAR SEAT RECLINING COVER LH
Using a T25 "TORX" socket wrench, remove the 2 screws.
Detach the guide and claw, and then remove the rear seat reclining cover LH.
71879C
7.REMOVE REAR SEAT INNER RECLINING COVER LH
Using a T25 "TORX" socket wrench, remove the screw.
Detach the clip.
Detach the 2 guides in the direction indicated by the arrow shown in the illustration, and then remove the rear seat inner reclining cover LH.
73390C
8.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Loosen the bolt.
Detach the guide and remove the rear No. 1 seat inner belt assembly LH.
72830
9.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Remove the 3 nuts and rear seat center armrest assembly from the rear seatback.
Using a T25 "TORX" socket wrench, remove the 2 bolts together with the 2 bushes.
Remove the rear seat armrest bracket from the rear seat center armrest assembly.
66990
10.REMOVE CUP HOLDER ASSEMBLY
Using moulding remover B, detach the 4 claws and remove the cup holder assembly.
72087
11.REMOVE REAR NO. 1 SEAT CENTER ARMREST COVER
Detach the 3 hooks and remove the rear No. 1 seat center armrest cover.
73709
12.REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY
Detach the 2 hooks of the separate type rear seatback cover.
Remove the 2 bolts and 2 tether anchor bracket sub-assemblies.
71931A
13.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 rear seat headrest supports.
71931B
14.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
15.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
Remove the nut.
Pass the rear center seat outer belt assembly through the rubber band of the separate type rear seatback cover and disconnect the floor anchor of the rear center seat outer belt assembly.
| *1 | Rubber Band |
Remove the screw.
Detach the 2 guides and remove the upper rear seatback lock bezel of the rear center seat outer belt assembly.
Detach the 8 hooks.
Pass the floor anchor of the rear center seat outer belt assembly through the hole of the separate type rear seatback cover with pad in the direction indicated by the arrow shown in the illustration and remove the separate type rear seatback cover with pad.
71078S
16.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the 9 hog rings and detach the 4 fasteners to remove the separate type rear seatback cover.
| *1 | Fastener |
73373F
17.REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Detach the 3 guides and remove the rear center seat outer belt assembly.
Remove the screw.
Detach the 2 guides and remove the rear seat shoulder belt hole cover.
73350C
18.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
Remove the nut.
Detach the guide and remove the rear center seat outer belt assembly.
72526B
19.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH
Pull the No. 1 reclining adjuster release handle LH and fold up the rear seat cushion frame sub-assembly LH.
Make sure that the rear seat cushion frame sub-assembly LH is locked.
Detach the clamp and disconnect the cable end of the No. 1 reclining adjuster release handle LH as shown in the illustration.
Detach the 2 cable clamps.
Detach the 2 cable clamps.
| *1 | Clamp |
| *2 | Cable Tie |
Cut off the cable tie.
Remove the 4 screws and No. 1 reclining adjuster release handle LH.
71016A
20.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Operate the lever of the rear seat ture lock sub-assembly and fold down the rear seat cushion frame sub-assembly LH.
Do not lock the rear seat cushion frame sub-assembly LH.
Using a T40 "TORX" socket wrench, remove the 2 bolts and rear seat cushion frame sub-assembly LH.
72094
21.REMOVE REAR SEAT TURN LOCK SUB-ASSEMBLY
Remove the 2 nuts and rear seat turn lock sub-assembly.
71018
22.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH
Remove the 5 bolts and rear seatback frame sub-assembly LH.