Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for CrewMax LH Side)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234310 REAR SEAT ASSEMBLY(for CrewMax LH Side) A

SEAT  REAR SEAT ASSEMBLY(for CrewMax LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71018 1.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

a.
B355142E02
1.75,2.938 0.854,3.042 0.854,3.042 1.406,2.771 true 0.49,2.208 0.375,2.792 true 2.583,2.292 2.99,1.354 true 2.917,2.417 2.99,1.354 false 2.99,1.354 3.073,1.354 false 0.688,3 0.865,3.188 0.177,0.188 10 false *1 0.271,2.833 0.552,3.063 0.281,0.229 10 false *2 3.083,1.271 3.333,1.5 0.25,0.229 10 false *2

Install the rear seatback frame sub-assembly LH with the 5 bolts.

Torque:
for Bolt A : 85 N*m (867 kgf*cm, 63 ft.*lbf)
for Bolt B : 45 N*m (459 kgf*cm, 33 ft.*lbf)

Text in Illustration
*1 Bolt A
*2 Bolt B


Hide 72094 2.INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY

a.

Install the rear seat turn lock sub-assembly with the 2 nuts.

Torque:
28 N*m (280 kgf*cm, 20 ft.*lbf)


Hide 71016A 3.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Using a T40 "TORX" socket wrench, install the rear seat cushion frame sub-assembly LH with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 72526B 4.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH

a.
B355205

Fold up the rear seat cushion frame sub-assembly LH.

HINT:

Make sure that the rear seat cushion frame sub-assembly LH is locked.



b.

Install the No. 1 reclining adjuster release handle LH with the 4 screws.


c.
B353881E01
2.439,0.638 2.717,0.898 0.279,0.260 10 *1 0.906,0.818 1.185,1.078 0.279,0.260 10 *2 2.41,0.707 2.304,0.707 2.304,0.707 2.169,0.915 false 2.304,0.707 2.274,1.528 false 1.532,0.876 1.112,0.905 false

Attach the 2 cable clamps.

Text in Illustration
*1 Clamp
*2 Cable Tie


d.

Install a new cable tie.


e.
B272385E02
2.195,2.233 2.349,2.414 0.154,0.181 10 *b 0.981,3.981 1.129,4.163 0.148,0.181 10 *c 2.244,3.981 2.402,4.163 0.157,0.181 10 *d 2.288,1.307 2.444,1.463 0.156,0.156 10 *a

Cut off the end of the cable tie as shown in the illustration.

Text in Illustration
*a Cut Here
*b 5 mm (0.20 in.)
*c Correct
*d Incorrect


f.
B353880

Attach the 2 cable clamps to connect the cable of the No. 1 reclining adjuster release handle LH as shown in the illustration.


g.

Connect the cable end of the No. 1 reclining adjuster release handle LH as shown in the illustration and attach the clamp.

B353878


h.

Pull the No. 1 reclining adjuster release handle LH and fold down the rear seat cushion frame sub-assembly LH.

B355143

HINT:

Make sure that the rear seat cushion frame sub-assembly LH is securely locked in the upright and retracted positions.



Hide 73350C 5.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

a.

Attach the guide and install the rear center seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73373F 6.INSTALL REAR SEAT SHOULDER BELT HOLE COVER

a.

Attach the 2 guides to install the rear seat shoulder belt hole cover with the screw.


b.

Attach the 3 guides to install the rear center seat outer belt assembly to the rear seat shoulder belt hole cover.


Hide 71078S 7.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.

Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 9 new hog rings as shown in the illustration.

B353873E01
5.606,0.54 5.873,0.738 0.267,0.198 10 *1 5.573,0.615 5.433,0.615 5.433,0.615 5.335,1.179 false 3.269,0.321 3.129,0.321 3.129,0.321 2.741,0.272 false 2.915,0.414 3.129,0.321 false 1.494,0.387 1.634,0.387 1.634,0.387 1.98,0.35 false 1.848,0.48 1.634,0.387 false 3.294,0.246 3.561,0.444 0.267,0.198 10 *2 1.326,0.323 1.593,0.521 0.267,0.198 10 *2

Text in Illustration
*1 Hog Ring Pliers *2 Fastener

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.

Attach the 4 fasteners.


Hide 8.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.
B353871

Pass the floor anchor of the rear center seat outer belt assembly through the hole of the separate type rear seatback cover with pad in the direction indicated by the arrow shown in the illustration.


b.

Attach the 8 hooks to install the separate type rear seatback cover with pad.


c.

Attach the 2 guides to install the upper rear seatback lock bezel of the rear center seat outer belt assembly with the screw.


d.
B353866E02
1.604,1.281 1.969,1.281 false 1.938,0.219 2.344,0.219 false 2.365,0.135 2.635,0.333 0.271,0.198 10 false *1 2,1.188 2.271,1.385 0.271,0.198 10 false *2

Pass the rear center seat outer belt assembly through the rubber band of the separate type rear seatback cover.

Text in Illustration
*1 Rubber Band
*2 Protruding Part


e.

Connect the floor anchor of the rear center seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

The anchor part of the rear center seat outer belt assembly must not overlap the protruding part.



Hide 71931B 9.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


Hide 71931A 10.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 73709 11.INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY

a.
B353862

Install the 2 tether anchor bracket sub-assemblies with the 2 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


b.

Attach the 2 hooks of the separate type rear seatback cover.


Hide 72087 12.INSTALL REAR NO. 1 SEAT CENTER ARMREST COVER

a.
B353858

Attach the 3 hooks to install the rear No. 1 seat center armrest cover.


Hide 66990 13.INSTALL CUP HOLDER ASSEMBLY

a.
B353857E02
1.021,2.042 1.229,2.208 0.208,0.167 10 true (1) 1.458,2.385 1.667,2.552 0.208,0.167 10 true (1) 1.188,1.365 1.396,1.531 0.208,0.167 10 true (2) 1.917,1.875 2.125,2.042 0.208,0.167 10 true (2)

Attach the 4 claws in the order shown in the illustration to install the cup holder assembly.


Hide 72830 14.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.

Install the rear seat armrest bracket and 2 bushes to the rear seat center armrest assembly.


b.

Using a T25 "TORX" socket wrench, install the 2 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


c.

Install the rear seat center armrest assembly with the 3 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 73390C 15.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

a.

Attach the guide.


b.

Tighten the bolt to install the rear No. 1 seat inner belt assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71879C 16.INSTALL REAR SEAT INNER RECLINING COVER LH

a.
B353852

Attach the 2 guides in the direction indicated by the arrow shown in the illustration.


b.

Attach the clip.


c.

Using a T25 "TORX" socket wrench, install the rear seat inner reclining cover LH with the screw.


Hide 71834D 17.INSTALL REAR SEAT RECLINING COVER LH

a.

Attach the guide and claw.


b.

Using a T25 "TORX" socket wrench, install the rear seat reclining cover LH with the 2 screws.


Hide 71076S 18.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.

Set the separate type rear seat cushion cover in place.


b.

Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 12 new hog rings as shown in the illustration.

B353847E02
5.271,1.177 5.396,0.688 5.396,0.688 5.521,0.688 false 1.948,0.99 2.125,1.229 false 2.906,1.01 2.719,1.24 false 5.552,0.625 5.823,0.792 0.271,0.167 10 false *1 2.125,1.24 2.396,1.406 0.271,0.167 10 false *2 2.583,1.24 2.854,1.406 0.271,0.167 10 false *2

Text in Illustration
*1 Hog Ring Pliers *2 Fastener

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.

Attach the 2 fasteners.


Hide 19.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.

Attach the 6 hooks to install the separate type rear seat cushion cover with pad.

B353844


Hide 72679 20.INSTALL REAR SEATBACK LOCK CONTROL BEZEL

a.

Attach the 4 claws to install the rear seatback lock control bezel.


b.
B353842

Close the 2 fasteners and attach the 2 hooks to close the separate type rear seat cushion cover.


c.

Fold in the 2 fasteners.

B353840


Hide 71960B 21.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

a.

Push the lock release button to release the lock, and then install the rear center seat headrest assembly.


Hide 71940A 22.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Push the 2 lock release buttons to release the lock, and then the rear seat headrest assembly.