Wear protective gloves. Sharp areas on the parts may injure your hands.
71940A
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Push the 2 lock release buttons indicated by the arrows in the illustration to release the lock, and then remove the rear seat headrest assembly.
72679
2.REMOVE REAR SEATBACK LOCK CONTROL BEZEL
Pull out the 2 fasteners.
Detach the hook and open the 2 fasteners, and then open the separate type rear seat cushion cover.
Detach the 4 claws on the backside of the rear seatback lock control bezel and remove the rear seatback lock control bezel.
3.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Detach the 5 hooks and remove the separate type rear seat cushion cover with pad.
71075S
4.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 12 hog rings and detach the 2 fasteners to remove the separate type rear seat cushion cover.
| *1 | Fastener |
71833D
5.REMOVE REAR SEAT RECLINING COVER RH
Using a T25 "TORX" socket wrench, remove the 2 screws.
Detach the guide and claw, and then remove the rear seat reclining cover RH.
71878C
6.REMOVE REAR SEAT INNER RECLINING COVER RH
Using a T25 "TORX" socket wrench, remove the screw.
Detach the 2 clips.
Detach the 2 guides in the direction indicated by the arrow shown in the illustration, and then remove the rear seat inner reclining cover RH.
73380C
7.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
Loosen the bolt.
Detach the guide and remove the rear No. 1 seat inner belt assembly RH.
73709
8.REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY
Remove the bolt and tether anchor bracket sub-assembly.
71931A
9.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 rear seat headrest supports.
10.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
Detach the 8 hooks and separate type rear seatback cover with pad.
71077S
11.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the 9 hog rings and detach the 4 fasteners to remove the separate type rear seatback cover.
| *1 | Fastener |
72525C
12.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH
Pull the No. 1 reclining adjuster release handle RH and fold up the rear seat cushion frame sub-assembly RH.
Make sure that the rear seat cushion frame sub-assembly RH is locked.
Detach the clamp and disconnect the cable end of the No. 1 reclining adjuster release handle RH as shown in the illustration.
Detach the 2 cable clamps.
Detach the 2 cable clamps.
| *1 | Clamp |
| *2 | Cable Tie |
Cut off the cable tie.
Remove the 4 screws and No. 1 reclining adjuster release handle RH.
71015A
13.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Operate the lever of the rear seat ture lock sub-assembly and fold down the rear seat cushion frame sub-assembly RH.
Do not lock the rear seat cushion frame sub-assembly RH.
Using a T40 "TORX" socket wrench, remove the 2 bolts and rear seat cushion frame sub-assembly RH.
72094
14.REMOVE REAR SEAT TURN LOCK SUB-ASSEMBLY
Remove the 2 nuts and rear seat turn lock sub-assembly.
71017
15.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH
Remove the 4 bolts and rear seatback frame sub-assembly RH.