Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for CrewMax RH Side)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234311 REAR SEAT ASSEMBLY(for CrewMax RH Side) A

SEAT  REAR SEAT ASSEMBLY(for CrewMax RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71017 1.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

a.

Install the rear seatback frame sub-assembly RH with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 72094 2.INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY

a.

Install the rear seat turn lock sub-assembly with the 2 nuts.

Torque:
28 N*m (280 kgf*cm, 20 ft.*lbf)


Hide 71015A 3.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.

Using a T40 "TORX" socket wrench, install the rear seat cushion frame sub-assembly RH with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 72525C 4.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH

a.
B378743

Fold up the rear seat cushion frame sub-assembly RH.

HINT:

Make sure that the rear seat cushion frame sub-assembly RH is locked.



b.

Install the No. 1 reclining adjuster release handle RH with the 4 screws.


c.
B355174E01
0.264,0.609 0.497,0.788 0.233,0.179 10 *1 1.988,0.783 2.222,0.962 0.233,0.179 10 *2 1.67,0.824 1.965,0.858 false 0.513,0.69 0.651,0.69 0.651,0.69 0.967,0.856 false 0.791,1.457 0.651,0.69 false

Attach the 2 cable clamps.

Text in Illustration
*1 Clamp
*2 Cable Tie


d.

Install a new cable tie.


e.
B272385E02
2.195,2.233 2.349,2.414 0.154,0.181 10 *b 0.981,3.981 1.129,4.163 0.148,0.181 10 *c 2.244,3.981 2.402,4.163 0.157,0.181 10 *d 2.288,1.307 2.444,1.463 0.156,0.156 10 *a

Cut off the end of the cable tie as shown in the illustration.

Text in Illustration
*a Cut Here
*b 5 mm (0.20 in.)
*c Correct
*d Incorrect


f.
B355173

Attach the 2 cable clamps to connect the cable of the No. 1 reclining adjuster release handle RH as shown in the illustration.


g.

Connect the cable end of the No. 1 reclining adjuster release handle RH as shown in the illustration and attach the clamp.

B355172


h.

Pull the No. 1 reclining adjuster release handle LH and fold down the rear seat cushion frame sub-assembly RH.

B355181

HINT:

Make sure that the rear seat cushion frame sub-assembly RH is securely locked in the upright and retracted positions.



Hide 71077S 5.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.

Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 9 new hog rings as shown in the illustration.

B355169E01
5.634,0.539 5.901,0.736 0.267,0.198 10 *1 5.602,0.613 5.462,0.613 5.462,0.613 5.363,1.177 false 2.828,0.29 2.687,0.29 2.687,0.29 2.3,0.241 false 2.42,0.493 2.687,0.29 false 1.024,0.317 1.164,0.317 1.164,0.317 1.509,0.281 false 1.4,0.517 1.164,0.317 false 2.853,0.215 3.120,0.412 0.267,0.198 10 *2 0.855,0.254 1.122,0.451 0.267,0.198 10 *2

Text in Illustration
*1 Hog Ring Pliers *2 Fastener

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.

Attach the 4 fasteners.


Hide 6.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.

Attach the 8 hooks to install the separate type rear seatback cover with pad.


Hide 71931A 7.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 73709 8.INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY

a.
B355165

Install the tether anchor bracket sub-assembly with the bolt.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 73380C 9.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

a.

Attach the guide.


b.

Tighten the bolt to install the rear No. 1 seat inner belt assembly RH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71878C 10.INSTALL REAR SEAT INNER RECLINING COVER RH

a.
B355163

Attach the 2 guides in the direction indicated by the arrow shown in the illustration.


b.

Attach the 2 clips.


c.

Using a T25 "TORX" socket wrench, install the rear seat inner reclining cover RH with the screw.


Hide 71833D 11.INSTALL REAR SEAT RECLINING COVER RH

a.

Attach the guide and claw.


b.

Using a T25 "TORX" socket wrench, install the rear seat reclining cover RH with the 2 screws.


Hide 71075S 12.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.

Set the separate type rear seat cushion cover in place.


b.

Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 12 new hog rings as shown in the illustration.

B355159E02
1.417,1.031 1.5,1.135 false 2.333,1.135 2.417,1.031 false 5.521,0.573 5.396,0.573 5.396,0.573 5.302,1.188 false 5.542,0.5 5.76,0.688 0.219,0.188 10 false *1 2.219,1.135 2.438,1.323 0.219,0.188 10 false *2 1.469,1.135 1.688,1.323 0.219,0.188 10 false *2

Text in Illustration
*1 Hog Ring Pliers *2 Fastener

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.

Attach the 2 fasteners.


Hide 13.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.

Attach the 5 hooks to install the separate type rear seat cushion cover with pad.

B355206


Hide 72679 14.INSTALL REAR SEATBACK LOCK CONTROL BEZEL

a.

Attach the 4 claws to install the rear seatback lock control bezel.


b.
B355154

Close the 2 fasteners and attach the hook to close the separate type rear seat cushion cover.


c.

Fold in the 2 fasteners.

B355151


Hide 71940A 15.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Push the 2 lock release buttons to release the lock, and then install the rear seat headrest assembly.