Home › Vehicle Interior › SEAT › FRONT SEATBACK HEATER(for Manual Seat) › 2015.08–2016.08
RM27M0U _58 Vehicle Interior _049136 SEAT _0234314 FRONT SEATBACK HEATER(for Manual Seat) A

SEAT  FRONT SEATBACK HEATER(for Manual Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


PROCEDURE

Hide 87510M 1.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH

a.

Set the front seatback heater assembly RH on the separate type front seatback cover.


b.
B356060

Using a tacker, install the front seatback heater assembly RH to the separate type front seatback cover with 8 new tack pins as shown in the illustration.

NOTICE:

Do not substitute other metal parts for tack pins.



Hide 71073S 2.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.
B354566E02
0.729,2.375 1.344,2.188 true 1.406,2.906 1.031,2.906 false 0.833,2.813 1.021,3 0.188,0.188 10 false *1 0.552,2.313 0.74,2.5 0.188,0.188 10 false *a

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


d.
B356059E01
1.283,0.523 0.63,0.523 false 0.454,0.446 0.610,0.591 0.156,0.145 10 *1 1.417,0.265 0.63,0.265 false 0.454,0.188 0.610,0.333 0.156,0.145 10 *1 1.331,1.12 0.63,1.12 false 2.186,0.523 2.839,0.523 false 2.053,0.265 2.839,0.265 false 2.138,1.12 2.839,1.12 false 0.454,1.043 0.610,1.189 0.156,0.145 10 *1 2.852,0.446 3.008,0.591 0.156,0.145 10 *1 2.852,0.188 3.008,0.333 0.156,0.145 10 *1 2.852,1.043 3.008,1.189 0.156,0.145 10 *1

Attach the 6 fasteners.

Text in Illustration
*1 Fastener


e.

Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.


f.

Attach the 2 hooks.

CAUTION:
·

For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

·

Make sure that the strap is not twisted after attach the 2 hooks.

·

Attach the 2 hooks securely.



i.

Slide each hook to attach them.


ii.

Install the 4 clips.



g.
B356808

Close the 2 fasteners.


h.

Pass the 2 wire harnesses through the separate type front seatback cover.


i.

Detach the hook.


Hide 3.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

When reusing a bolt:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




b.
B356054

Install the separate type front seatback assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


c.
B356053E01
0.14,0.183 0.317,0.336 0.177,0.152 10 *1 1.09,0.267 0.329,0.267 false 0.14,0.798 0.317,0.950 0.177,0.152 10 *2 1.021,0.882 0.329,0.882 false 1.056,0.427 0.471,0.883 0.471,0.883 1.137,1.493 false

Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly RH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


d.

Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly RH.


e.

Connect the connector.


Hide 71867A 4.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD RH

a.
B356065

Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield RH.


b.

Install the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 71811D 5.INSTALL FRONT SEAT CUSHION SHIELD RH

a.
U152083E01
3.13,1.935 3.332,2.114 0.202,0.179 10 (1) 1.302,0.789 1.504,0.968 0.202,0.179 10 (2)

Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield RH.


b.

Install the 3 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


c.

Connect the 2 rubber bands.


Hide 72525A 6.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.

Attach the claw to install the reclining adjuster release handle RH.


Hide 7.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the driver seat (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION).