Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM27M0U _58 Vehicle Interior _049137 DOOR LOCK _0234323 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

U152758E02
5.865,5.271 6.896,5.448 1.031,0.177 10 false Main Body ECU 0.229,4.563 1.656,4.74 1.427,0.177 10 false Door Control Receiver 1.083,1.688 1.573,1.906 0.49,0.219 10 false +B 0.979,2.479 1.469,2.698 0.49,0.219 10 false RDA 4.656,1.667 5.573,1.885 0.917,0.219 10 false from Battery 0.969,3.302 1.458,3.521 0.49,0.219 10 false PRG 5.99,1.042 6.479,1.26 0.49,0.219 10 false ACT+ 5.99,2.479 6.479,2.698 0.49,0.219 10 false RDA 5.99,3.302 6.479,3.521 0.49,0.219 10 false PRG 3.583,4.521 5.083,4.74 1.5,0.219 10 false Unlock Warning Switch 5.99,4.156 6.479,4.375 0.49,0.219 10 false KSW 0.969,4.094 1.458,4.313 0.49,0.219 10 false GND 1.396,1.563 1.615,1.76 0.219,0.198 10 false 5 1.385,3.177 1.604,3.375 0.219,0.198 10 false 3 1.396,2.354 1.615,2.552 0.219,0.198 10 false 2 1.385,3.948 1.604,4.146 0.219,0.198 10 false 1 5.656,2.281 5.875,2.479 0.219,0.198 10 false 12 5.656,3.115 5.875,3.313 0.219,0.198 10 false 10 5.698,3.958 5.917,4.156 0.219,0.198 10 false 5 3.656,4.021 3.875,4.219 0.219,0.198 10 false 2 4.49,4.021 4.708,4.219 0.219,0.198 10 false 1 2.563,1.823 3.104,1.979 0.542,0.156 10 false ECU-B1 0.229,4.406 0.875,4.635 0.646,0.229 10 false Q7 5.667,4.146 5.865,4.313 0.198,0.167 10 false J1 5.667,3.292 5.865,3.458 0.198,0.167 10 false J3 3.594,4.365 4.01,4.573 0.417,0.208 10 false J18 5.667,2.479 5.865,2.646 0.198,0.167 10 false J3 3.906,1.052 5.115,1.438 1.208,0.385 10 false to Door Lock Motor

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION FUNCTION
a.

Check the power door lock operation function (see page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Each door locks and unlocks normally.




OK

2.CHECK KEY REMINDER WARNING OPERATION FUNCTION

NG

2.CHECK KEY REMINDER WARNING OPERATION FUNCTION
a.

Check the key reminder buzzer operation function (see page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).

HINT:

If the key reminder buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.


OK:

Key reminder buzzer operates normally.




OK

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER

NG

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER
a.

Check whether the wireless door lock control functions operate normally with another registered vehicle transmitter.

OK:

Wireless door control functions operate normally




OK

4.CHECK TRANSMITTER BATTERY

NG

5.CHECK ELECTRICAL NOISE
4.CHECK TRANSMITTER BATTERY
a.

Remove the battery from the inoperative wireless door control transmitter (see page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
Battery positive (+) side - Battery negative (-) side Always 2.2 to 3.2 V




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

REPLACE TRANSMITTER BATTERY

5.CHECK ELECTRICAL NOISE
a.

Move the transmitter near the vicinity of the door control receiver.

HINT:
·

For Regular Cab, refer to the PARTS LOCATION for the location of the door control receiver (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Regular Cab)>COMPONENTS).

·

For Double Cab, refer to the PARTS LOCATION for the location of the door control receiver (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Double Cab)>COMPONENTS).

·

For CrewMax, refer to the PARTS LOCATION for the location of the door control receiver (see page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for CrewMax)>REMOVAL).




b.

Press and hold either the LOCK or UNLOCK transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

OK:

Wireless door control functions operate normally


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in outputs from the door control transmitter was the cause. There is a high probability that electrical noise was the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.





OK

FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT

NG

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
a.
B443029E01
0.24,1.396 0.635,1.625 0.396,0.229 0.354,3.625 0.75,3.854 0.396,0.229 2.385,1.281 2.688,1.198 true 0.719,1.813 1.177,1.594 true 1.25,4.417 1.479,3.99 true 1.896,4.417 1.708,4 true 0.188,0.167 2.448,0.542 2.26,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.208,2.5 2.469,2.875 2.26,0.375 10 false Front view of wire harness connector: (to Door Control Receiver) 0.365,1.427 0.573,1.604 0.208,0.177 10 false J3 0.458,3.656 0.667,3.833 0.208,0.177 10 false Q7 2.75,1.115 3.208,1.313 0.458,0.198 10 false PRG 0.5,1.844 0.844,2.042 0.344,0.198 10 false RDA 0.917,4.354 1.375,4.552 0.458,0.198 10 false RDA 1.948,4.375 2.406,4.573 0.458,0.198 10 false PRG

Disconnect the J3 ECU connector.


b.

Disconnect the Q7 receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J3-12 (RDA) - Q7-2 (RDA) Always Below 1 Ω
J3-10 (PRG) - Q7-3 (PRG)
J3-12 (RDA) - Q7-2 (RDA) - Body ground Always 10 kΩ or higher
J3-10 (PRG) - Q7-3 (PRG) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U151864E02
1.208,2.146 0.99,2.448 true 2.208,2.135 2.469,2.438 true 0.104,0.167 2.375,0.615 2.271,0.448 10 false Front view of wire harness connector: (to Door Control Receiver) 2.521,2.385 2.844,2.583 0.323,0.198 10 false +B 0.646,2.385 1.01,2.583 0.365,0.198 10 false GND 0.385,1.792 0.677,2.083 0.292,0.292 10 false Q7

Disconnect the Q7 receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
Q7-5 (+B) - Body Ground Always 11 to 14 V


Standard resistance:
Tester Connection Condition Specified Condition
Q7-1 (GND) - Body ground Always Below 1 Ω




OK

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)
U152019E02
1.865,2.469 2.24,2.833 true 2.313,2.75 2.698,2.948 0.385,0.198 10 false RDA 0.729,2.01 1.063,2.208 0.333,0.198 10 false Q7 0.198,0.063 2.688,0.438 2.49,0.375 10 false Component with harness connected: (Door Control Receiver)

a.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Q7-2 (RDA) - Body ground Ignition switch OFF, all doors closed and transmitter switch not pressed 11 to 14 V
Ignition switch OFF, all doors closed and transmitter switch pressed Pulse generation


OK:

Door control receiver outputs pulse generation.


Result
Result Proceed to
OK A
NG (for Regular Cab) B
NG (for Double Cab) C
NG (for CrewMax) D



A

REPLACE MAIN BODY ECU

B

C

D