Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK(for CrewMax)
RM27M0U _58 Vehicle Interior _049137 DOOR LOCK _0234330 REAR DOOR LOCK(for CrewMax) G

DOOR LOCK  REAR DOOR LOCK(for CrewMax)  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock and check operation of the door lock.

B443038E01
5.396,1.781 5.5,2.188 true 4.896,2.188 5,1.792 true 4.51,1.583 4.854,1.583 true 5.521,1.573 5.865,1.573 true 0.646,2.156 1.052,2.354 0.406,0.198 10 false Lock 4.406,1.521 4.583,1.719 0.177,0.198 10 false L 4.01,0.438 6.458,0.802 2.448,0.365 10 false Component without harness connected: (Rear Door Lock LH) 4.833,2.229 5.01,2.427 0.177,0.198 10 false E 5.927,1.5 6.167,1.698 0.24,0.198 10 false UL 5.406,2.219 5.896,2.417 0.49,0.198 10 false LSSR 2.323,2.333 2.854,2.531 0.531,0.198 10 false Unlock

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




Hide 69050A 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.

Check the door lock motor.

i.

Apply battery voltage to the door lock and check operation of the door lock.

B443039E01
4.469,1.573 4.854,1.573 true 5.521,1.573 5.906,1.573 true 5.375,1.781 5.479,2.073 true 4.854,2.094 4.99,1.792 true 3.833,0.396 6.292,0.771 2.458,0.375 10 false Component without harness connected: (Rear Door Lock RH) 1.396,2.24 2,2.448 0.604,0.208 10 false Unlock 3.146,2.063 3.75,2.271 0.604,0.208 10 false Lock 4.344,1.5 4.5,1.698 0.156,0.198 10 false L 5.969,1.49 6.25,1.677 0.281,0.188 10 false UL 4.792,2.135 4.948,2.333 0.156,0.198 10 false E 5.417,2.094 5.865,2.302 0.448,0.208 10 false LSSR

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the door lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.