Home › Vehicle Interior › ENGINE HOOD / DOOR › REAR DOOR(for Double Cab)
RM27M0U _58 Vehicle Interior _049138 ENGINE HOOD / DOOR _0234338 REAR DOOR(for Double Cab) A

ENGINE HOOD / DOOR  REAR DOOR(for Double Cab)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (see page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67872 1.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B167089

Attach the 34 clips to install the weatherstrip.

HINT:

If clips are damaged during installation, replace them.



Hide 68640A 2.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.
B166256

Apply MP grease to the sliding areas of the door check.


b.

Install the door check to the door panel with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 67888A 3.INSTALL REAR NO. 2 DOOR WEATHERSTRIP LH

a.
B166257

Attach the 7 clips to install the weatherstrip.


Hide 69240 4.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B166254

Install the rear door outside handle with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Install the 2 hole plugs.


Hide 69332 5.INSTALL REAR DOOR LOCK OPEN ROD LH

Hide 67836H 6.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

Hide 69780B 7.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B167682E02
1.927,0.552 2.073,0.552 2.073,0.552 2.219,1.135 false 0.406,0.49 1.906,0.854 1.5,0.365 10 true End Cap (Color: Yellow)

Install the rear door inside locking cable.


b.
B266908

Attach the 3 claws.


Hide 69740D 8.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B165670E06
2.125,1.125 2.125,1.594 false 1.375,1.625 2.854,2 1.479,0.375 10 true End Cap (Color: Yellow)

Install the rear door lock remote control cable.


Hide 69060A 9.INSTALL REAR DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating parts of the front door lock.


b.

Install a new door lock wire harness packing to the door lock.

NOTICE:
·

When reusing a door lock that has been removed, replace the packing in the connecting part with a new packing.

·

Be careful that no grease or dirt sticks to the packing surface in the connecting part.

·

Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.




c.
B166253

Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 85710E 10.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the regulator motor.


b.
B166252

Using a T25 ''TORX'' driver, install the motor with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

For a new front window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



Hide 69804 11.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the rear door power window regulator.


b.
B166251E04
1.323,0.24 3.104,0.323 3.104,0.323 0.823,1.792 false 0.167,1.792 0.365,2 0.198,0.208 10 false 2 0.927,1.927 1.125,2.135 0.198,0.208 10 false 3 0.583,1.771 0.781,2.021 0.198,0.25 10 false 4 1.458,1.917 1.615,2.125 0.156,0.208 10 true 1 0.271,0.156 1.25,0.51 0.979,0.354 10 true Temporary Bolt

Loosely install the temporary bolt onto the window regulator.


c.

Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.


d.

Temporarily install the window regulator with the 3 bolts, and tighten the temporary bolt so that it contacts the door panel.


e.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68163 12.INSTALL REAR OUTER DOOR GLASS WEATHERSTRIP

Hide 68192B 13.INSTALL REAR NO. 2 DOOR GLASS RUN LH

a.

Install the rear door glass run to the rear door window front lower guide.


Hide 67406B 14.INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

a.
B167093

Install the rear door front window guide to the door panel with the 2 bolts.


Hide 68104 15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B167085

Slide the rear door glass to install it as shown in the illustration.

NOTICE:

Be careful not to damage the glass.



Hide 68192B 16.INSTALL REAR NO. 2 DOOR GLASS RUN LH

a.

Install the rear door glass run to the rear door window rear lower frame.


Hide 67408F 17.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

a.
B166247

Install the rear door rear lower window frame LH to the door panel with the 4 bolts.


Hide 68152C 18.INSTALL REAR DOOR GLASS RUN LH

a.
B166248

Install the rear door glass run.


Hide 67842E 19.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.
B166246

Attach the 2 clamps to install the rear door service hole cover.

NOTICE:
·

When installing the service hole cover, pull out the links through the service hole cover.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the sealing quality.




Hide 67626C 21.INSTALL REAR NO. 2 DOOR TRIM BRACKET

a.
B166245

Install the bracket with the 2 screws.


Hide 68174A 22.INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH

Hide 67604 23.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B165684E04
2.531,1.51 2.698,1.958 2.698,1.958 2.458,1.958 false 2.167,0.875 2.792,0.167 2.792,0.167 2.417,0.167 false 0.927,0.063 2.385,0.458 1.458,0.396 10 true End Cap (Color: White) 1.021,1.854 2.49,2.156 1.469,0.302 10 true End Cap (Color: Green)

Connect the 2 cables to the inside handle.


b.

Attach the inside handle's knob to the door trim board.


c.
B166244E02
0.51,0.698 0.51,0.969 false 0.417,0.979 0.771,1.323 0.354,0.344 10 false Clip

Attach the 9 clips to install the door trim board.


d.

Install the inside handle and door trim board to the door trim panel with the screw.


e.

Install the door trim board to the door panel with the screw


f.

Attach the clip.


Hide 74222A 24.INSTALL REAR DOOR ARMREST COVER LH

Hide 67674A 25.INSTALL REAR DOOR FRAME GARNISH LH

a.
B167090

Attach the 4 clips to install the rear door frame garnish.


Hide 84810D 26.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 74272A 27.INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH

a.
E278383

Connect the connector.


b.
E278385

Attach the 2 clips and 5 claws to install the rear upper door armrest base panel LH.


Hide 69284D 28.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B168093

Attach the 4 claws to install the bezel plug.


Hide 29.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL