Home › Vehicle Interior › ENGINE HOOD / DOOR › HOOD LOCK CONTROL CABLE ASSEMBLY
RM27M0U _58 Vehicle Interior _049138 ENGINE HOOD / DOOR _0234339 HOOD LOCK CONTROL CABLE ASSEMBLY A

ENGINE HOOD / DOOR  HOOD LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

a.

Pass the hood lock control cable assembly into the engine room.


b.

Pass the rear end of the hood lock control cable assembly through the grommet until the cable stopper is attached to the grommet.


c.

Pass the front end of the hood lock control cable assembly through the upper radiator support.


d.

Attach the hood lock control cable assembly to the clamps as shown in the illustration.

B354842E01
1.784,1.637 1.984,1.820 0.200,0.183 10 *1 1.508,1.703 1.778,1.703 false 6.55,2.282 6.750,2.465 0.200,0.183 10 *1 3.606,0.257 3.769,0.440 0.163,0.183 10 *1 3.642,1.024 3.842,1.207 0.200,0.183 10 *3 5.59,0.748 5.790,0.931 0.200,0.183 10 *1 6.274,2.347 6.544,2.347 false 6.229,2.807 6.274,2.347 false 5.752,0.818 5.92,0.818 false 5.92,0.818 6.204,1.091 false 1.149,0.902 1.407,1.137 0.258,0.235 10 *2 5.535,1.195 5.793,1.429 0.258,0.235 10 *2 6.64,2.55 6.898,2.785 0.258,0.235 10 *2 1.33,0.961 1.5,0.961 false 1.5,0.961 1.619,1.344 false 6.63,2.625 6.574,2.625 false 5.927,1.266 5.682,1.266 false 3.8,1.099 3.905,1.099 false 3.905,1.099 3.962,1.06 false 3.735,0.328 3.791,0.328 false 3.791,0.328 3.851,0.43 false

Text in Illustration
*1 Hood Lock Control Cable Assembly *2 Clamp
*3 Grommet - -


Hide 53601 2.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.


b.

Attach the 3 claws to install the hood lock lever sub-assembly.


Hide 53510 3.INSTALL HOOD LOCK ASSEMBLY

a.

Apply MP grease to the sliding areas of the hood lock assembly.

B356561E01
1.45,0.179 1.643,0.372 0.193,0.193 10 *a 4.103,0.179 4.296,0.372 0.193,0.193 10 *b

Text in Illustration
*a Back Side *b Front Side


b.

Connect the hood lock control cable assembly.


c.

Install the hood lock assembly.


d.

Install the 2 bolts and hood lock bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install a new hood lock nut cap.


f.

w/ Engine Hood Courtesy Switch:

i.

Connect the connector.


ii.

Attach the clamp.



Hide 53101 4.INSTALL RADIATOR GRILLE SUB-ASSEMBLY