READ DATA LIST
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch OFF.
Connect the Techstream to the DLC3.
Turn the ignition switch ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) | Actual vehicle speed is displayed | - |
| CCS Mem Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) | Actual vehicle speed stored in memory | - |
| Cruise Operation Status | Shift lever position signal / ON or OFF | ·
for 1UR-FE, 3UR-FE, 3UR-FBE: ON: Shift lever position D (6th, 5th or 4th gear) OFF: Shift lever position except D (6th, 5th or 4th gear) ·
for 1GR-FE: ON: Shift lever position D (5th or 4th gear) OFF: Shift lever position except D (5th or 4th gear) |
- |
| Cruise Control | Cruise control / ON or OFF | ON: Cruise control is SET
OFF: Cruise control is UNSET |
- |
| CCS Indicator M-CPU | Cruise control indicator light (Main CPU) / ON or OFF | ON: Cruise control indicator light is ON
OFF: Cruise control indicator light is OFF |
- |
| CCS Ready M-CPU | Cruise control system standby condition (Main CPU) / ON or OFF | ON ←→ OFF: Changes each time main switch is pushed | - |
| Main SW M-CPU | Cruise control main switch (Main CPU) / ON or OFF | ON: Cruise control main switch (Main CPU) is SET
OFF: Cruise control main switch (Main CPU) is UNSET |
- |
| Cancel Switch | CANCEL switch / ON or OFF | ON: CANCEL switch is SET
OFF: CANCEL switch is UNSET |
- |
| SET/COAST Switch | -/SET switch / ON or OFF | ON: -/SET switch is SET
OFF: -/SET switch is UNSET |
- |
| RES/ACC Switch | +/RES switch / ON or OFF | ON: +/RES switch is SET
OFF: +/RES switch is UNSET |
- |
| Stp Light SW M-CPU | Stop light switch signal (Main CPU) / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Throttle Opening Angle | Cruise throttle opening angle / min.: 0°, max.: 124.5° | Actual demanded throttle angle | - |
| Brake Cancel Switch | Brake pedal cancel switch signal / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Distance Control* | Cruise cancel signal / ON or OFF | ON: Cruise control cancel
OFF: cruise control operating |
- |
*: for 4WD
PERFORM ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch OFF.
Connect the Techstream to the DLC3.
Turn the ignition switch ON.
Turn the Techstream on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the Techstream, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Cruise | Cruise control indicator light operation | OFF or ON | - |
| Indicat. SET | Cruise control SET indicator light operation | OFF or ON | - |