Home › Engine / Hybrid System › 1UR-FE STARTING › STARTER(for 2.0 kW Type)
RM27M0U _51 Engine / Hybrid System _049144 1UR-FE STARTING _0234363 STARTER(for 2.0 kW Type) A

1UR-FE STARTING  STARTER(for 2.0 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
U151719E02
0.396,1.76 1.979,1.938 1.583,0.177 10 false High-temperature grease

Apply high-temperature grease to the areas of the starter pinion drive lever indicated in the illustration.


b.

Install the starter pinion drive lever and rubber seal to the starter center bearing clutch.


c.

Install the starter center bearing clutch together with the starter pinion drive lever and rubber seal to the starter drive housing.


d.
U151720E01
0.424,1.715 2.048,1.889 1.624,0.174 10 High-temperature grease

Apply high-temperature grease to the planetary gears and pins of the starter center bearing clutch as shown in the illustration.


e.

Install the 3 planetary gears.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature to the starter yoke.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed causing the magnet to break.



Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A215977

Push out the 4 brushes from the brush holder so that they are held in place by the springs as shown in the illustration.


b.
A215968

Install the brush holder to the starter armature and push in the 4 brushes.

NOTICE:

Check that the positive (+) lead wires are not grounded.



c.
U151600E02
0.865,0.219 1.031,0.219 1.031,0.219 1.542,0.917 false 0.781,0.594 0.865,0.594 0.865,0.594 1.323,0.948 false 2.625,1.26 2.521,1.26 2.521,1.26 2.104,0.917 false 0.271,0.135 0.938,0.292 0.667,0.156 10 false Grommet 0.24,0.5 0.823,0.813 0.583,0.313 10 false Negative Side 2.698,1.167 3.219,1.49 0.521,0.323 10 false Positive Side

Insert the grommet between the positive side and negative side.


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A258320E04
1.708,0.792 1.99,0.583 1.99,0.583 2.104,0.583 false 1.49,1.188 1.396,1.479 1.396,1.479 1.302,1.479 false 2.146,0.5 2.563,0.688 0.417,0.188 10 false Key-A 0.906,1.396 1.323,1.583 0.417,0.188 10 false Key-B

Install the starter armature plate to the starter yoke.

NOTICE:

Install the starter armature plate so that the keyway is positioned between key A and key B.



b.

Install the starter commutator end frame with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


c.
A258321E03
1.979,1.396 1.844,1.635 1.844,1.635 1.74,1.635 false 0.958,1.01 0.875,1.333 0.875,1.333 0.875,1.406 false 1.469,1.542 1.74,1.719 0.271,0.177 10 false Key 0.635,1.396 1.156,1.573 0.521,0.177 10 false Keyway

Align the key of the starter yoke with the keyway located on the starter drive housing.


d.

Using a T25 "TORX" socket wrench, install the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
U151721E02
0.427,1.75 2.021,1.927 1.594,0.177 10 false High-temperature grease

Apply high-temperature grease to the plunger hook.


b.

Hang the plunger of the magnet starter switch onto the drive lever from the upper side.


c.

Install the magnet starter switch with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the lead wire to the magnet starter switch with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)