Home › Engine / Hybrid System › 1UR-FE STARTING › STARTER(for 1.6 kW Type)
RM27M0U _51 Engine / Hybrid System _049144 1UR-FE STARTING _0234368 STARTER(for 1.6 kW Type) G

1UR-FE STARTING  STARTER(for 1.6 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a think cable must be used.

If not, the cable may became hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds.


a.
A215981E02
3.042,0.229 3.167,0.229 3.167,0.229 2.74,1.417 false 1.563,2.25 1.708,2.25 1.708,2.25 2.531,1.646 false 2.25,0.156 3.042,0.333 0.792,0.177 10 false Terminal 50 0.833,2.167 1.563,2.344 0.729,0.177 10 false Terminal C

Perform a pull-in test.

i.

Remove the nut, and then disconnect the field coil lead wire from terminal C.


ii.

Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



b.
A215980E02
1.604,2.271 1.708,2.271 1.708,2.271 2.49,1.646 false 0.865,2.198 1.604,2.375 0.74,0.177 10 false Terminal C

Perform a holding test.

i.

When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the magnet starter switch assembly.



c.
A215978E01
1.316,2.17 2.125,2.330 0.809,0.161 10 Starter Body 1.259,2.252 1.151,2.252 1.151,2.252 1.583,1.821 false

Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform an operation test without load.

i.

Connect the field coil lead wire to terminal C.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Mount the starter in a vise between aluminum plates.


iii.
A215979E02
1.99,0.219 2.083,0.219 2.083,0.219 2.438,1.323 false 2.125,2.354 2.198,2.354 2.198,2.354 2.615,1.563 false 1.188,0.146 1.99,0.313 0.802,0.167 10 false Terminal 30 1.323,2.281 2.125,2.479 0.802,0.198 10 false Terminal 50

Connect the battery and ammeter to the starter as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A082640

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assembly.



b.
A217470E02
1.375,0.177 1.281,0.177 1.281,0.177 1.281,0.99 false 1.74,1.979 1.635,1.979 1.635,1.979 1.396,1.604 false 1.427,0.094 2.146,0.25 0.719,0.156 10 false Terminal C 1.792,1.896 2.563,2.052 0.771,0.156 10 false Terminal 50

Check if the pull-in coil has an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A217471E02
0.99,1.125 1.094,1.125 1.094,1.125 1.594,1.646 false 2.396,0.198 2.271,0.198 2.271,0.198 1.99,0.76 false 0.188,1.052 0.969,1.229 0.781,0.177 10 false Terminal 50 2.448,0.125 3.25,0.281 0.802,0.156 10 false Switch Body

Check if the holding coil has an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the appearance.

If the surface is dirty or burnt, restore the surface with sandpaper (No. 400) or on a lathe.


b.
A215965E03
1.396,1.688 1.49,1.688 1.49,1.688 1.99,1.167 true 2.656,1.302 2.573,1.302 2.573,1.302 2.188,0.896 true 2.708,1.219 3.302,1.365 0.594,0.146 10 false Segment 0.729,1.604 1.396,1.781 0.667,0.177 10 false Segment

Measure the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.


ii.
A215966E04
2.531,1.667 2.469,1.667 2.469,1.667 2.052,1.188 true 0.76,0.792 0.833,0.792 0.833,0.792 1.292,1.125 true 2.583,1.573 3.188,1.729 0.604,0.156 10 false Segment 0.094,0.719 0.75,0.906 0.656,0.188 10 false Coil Core

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.
A215967

Check the commutator circle runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Standard runout:

0.02 mm (0.000787 in.)


Maximum runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



d.
A215958

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

29.0 mm (1.14 in.)


Minimum diameter:

28.0 mm (1.10 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


e.
A062965

Check that the undercut portion is clean and free of foreign matter. Smooth out the edge.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, increase the depth using a hacksaw blade.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A215975

Using a vernier caliper, measure the brush length.

Standard length:

14.4 mm (0.567 in.)


Minimum length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


b.
A218984E01
0.638,1.703 1.044,1.852 0.406,0.149 10 Brush 2.354,1.411 3.182,1.581 0.828,0.170 10 Brush Spring

Inspect the load of the brush spring.

i.

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

16 to 20 N (1.7 to 2 kgf, 3.6 to 4.5 lbf)


Minimum spring load:

6.7 N (0.7 kgf, 1.5 lbf)


If the load is less than the minimum, replace the starter brush holder assembly.



Hide 28021 5.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planet gears, and the internal gear and pinion gear of the starter center bearing clutch for wear or damage.

If any of the gears is damaged, replace the gear or starter center bearing clutch sub-assembly.


b.
A215964E02
1.281,1.542 1.625,1.688 0.344,0.146 10 false Lock 1.698,0.281 2.021,0.427 0.323,0.146 10 false Free

Hold the starter clutch, rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter center bearing clutch sub-assembly.