Home › Engine / Hybrid System › 1UR-FE STARTING › STARTER(for 1.6 kW Type)
RM27M0U _51 Engine / Hybrid System _049144 1UR-FE STARTING _0234368 STARTER(for 1.6 kW Type) A

1UR-FE STARTING  STARTER(for 1.6 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A215961E01
2.245,0.025 3.136,0.346 0.892,0.321 10 Starter Pinion Drive Lever 2.245,0.954 3.197,1.269 0.953,0.316 10 Starter Center Bearing Clutch 2.17,0.103 2.039,0.103 2.039,0.103 1.336,0.27 false 2.205,1.031 2.084,1.031 2.084,1.031 1.714,1.361 false

Apply high temperature grease to the areas of the starter pinion drive lever indicated in the illustration.


b.

Install the starter pinion drive lever and rubber seal to the starter center bearing clutch.


c.

Install the starter center bearing clutch together with the starter pinion drive lever and rubber seal into the starter drive housing.


Hide 28255 2.INSTALL PLANETARY GEAR

a.
A215963

Apply high temperature grease to the planetary gears and pins of the starter center bearing clutch.


b.

Install the 3 planetary gears.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A215959E02
2.021,0.115 1.948,0.115 1.948,0.115 1.781,0.583 false 1.052,1.656 1.156,1.656 1.156,1.656 1.25,1.563 false 2.063,0.042 3.146,0.198 1.083,0.156 10 false Starter Armature 0.25,1.573 1.063,1.729 0.813,0.156 10 false Starter Yoke

Install the starter armature to the starter yoke.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed causing the magnet to break.



Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A215977

Push out the 4 brushes from the brush holder so that they are held in place by the springs, as shown in the illustration.


b.
A215968

Install the brush holder to the starter armature and push in the 4 brushes.


c.
U151599E02
0.844,0.198 1.01,0.198 1.01,0.198 1.542,0.906 false 0.781,0.594 0.865,0.594 0.865,0.594 1.323,0.948 false 2.625,1.26 2.521,1.26 2.521,1.26 2.104,0.917 false 0.25,0.115 0.917,0.271 0.667,0.156 10 false Grommet 0.229,0.51 0.813,0.823 0.583,0.313 10 false Negative side 2.677,1.177 3.198,1.5 0.521,0.323 10 false Positive side

Insert grommet between the positive (+) side and negative side.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A215971

Fit the clamp of the brush holder into the starter commutator end frame.


b.
A215957

Install the commutator end frame with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 28177 6.INSTALL STARTER ARMATURE PLATE

a.

Install the starter armature plate to the starter yoke.

NOTICE:
A215972E02
2.198,0.552 2.104,0.552 2.104,0.552 1.719,0.813 false 1.188,1.615 1.25,1.615 1.25,1.615 1.479,1.167 false 2.271,0.438 2.792,0.635 0.521,0.198 10 false Key-A 0.688,1.542 1.188,1.719 0.5,0.177 10 false Key-B

Install the starter plate so that the keyway is positioned between key-A and key-B.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A215973E02
2.823,1.292 2.677,1.896 2.677,1.896 2.594,1.896 false 1.781,1.604 1.51,0.823 1.51,0.823 1.417,0.823 false 1.146,0.729 1.427,0.906 0.281,0.177 10 false Key 2.073,1.802 2.594,1.948 0.521,0.146 10 false Keyway

Align the key of the starter yoke with the keyway located on the starter drive housing.


b.
A215955

Using a T25 "TORX" socket wrench, install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
U151678

Apply high temperature grease to the plunger hook.


b.

Hang the plunger of the magnet starter switch onto the drive lever from the upper side.


c.
A215953

Install the magnet starter switch with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
A215952

Connect the lead wire to the magnet starter switch and connect it with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)