Home › Engine / Hybrid System › 1UR-FE CHARGING › GENERATOR
RM27M0U _51 Engine / Hybrid System _049146 1UR-FE CHARGING _0234376 GENERATOR A

1UR-FE CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

A187035E06
3.073,1.229 3.073,0.573 false 2.427,1.521 2.427,1.365 2.427,1.365 2.833,0.719 false 0.927,1.333 1.219,1.563 0.292,0.229 10 true Turn 1.667,1.854 1.979,2 0.313,0.146 10 false Hold 2.125,1.542 2.719,1.719 0.594,0.177 10 false SST 1-B 2.76,1.25 3.313,1.396 0.552,0.146 10 false SST 1-A

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021


a.

Clamp the generator housing stay in a vise.


b.

Install SST 1-A to the pulley shaft.


c.

Install SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is secured on the rotor shaft.



e.
A187036E05
2.563,0.427 2.688,0.427 2.688,0.427 2.792,0.885 false 2.031,0.333 2.469,0.552 0.438,0.219 10 false SST 2 2.375,1.354 2.76,1.552 0.385,0.198 10 true Insert

Insert SST 2, and attach the pulley nut to SST 2.


f.
A187037E04
2.979,0.719 3.292,0.865 0.313,0.146 10 false Turn 1.698,1.729 2.021,1.927 0.323,0.198 10 true Hold

To loosen the pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.



g.

Remove SST 2 from the generator.


h.
A187038E06
3.063,1.219 3.063,0.615 false 2.594,1.552 2.594,1.323 2.594,1.323 2.833,0.75 false 1.219,1.469 1.531,1.667 0.313,0.198 10 true Turn 1.938,1.688 2.25,1.875 0.313,0.188 10 true Hold 2.323,1.583 2.906,1.823 0.583,0.24 10 true SST 1-B 2.76,1.24 3.313,1.396 0.552,0.156 10 false SST 1-A

Turn SST 1-B, and remove SST 1-A and B.


i.

Remove the pulley nut and pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A163586

Place the generator on the pulley.


b.

Remove the 3 nuts and end cover.


c.
A156408

Remove the terminal insulator.


Hide 27370 3.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A156409

Remove the 2 screws and brush holder.


Hide 27360 4.REMOVE GENERATOR COIL ASSEMBLY

a.
A156414

Remove the 4 bolts.


b.
A156415E01
0.354,0.346 0.667,0.543 0.313,0.198 10 SST 2.904,0.48 3.277,0.677 0.374,0.198 10 Turn 0.247,1.512 0.620,1.709 0.374,0.198 10 Hold 1.327,0.792 0.721,0.438 false

Using SST, remove the coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.

Remove the generator washer.


Hide 27330 5.REMOVE GENERATOR ROTOR ASSEMBLY

Hide 27310B 6.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A156416

Remove the 4 screws and retainer plate.


b.
A156417E01
2.377,0.955 2.721,1.136 0.344,0.181 10 SST 1.673,1.377 2.333,1.042 false 2.333,1.042 1.68,0.979 false

Using SST and a hammer, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)