Home › Engine / Hybrid System › 3UR-FE CHARGING › GENERATOR
RM27M0U _51 Engine / Hybrid System _049147 3UR-FE CHARGING _0234378 GENERATOR G

3UR-FE CHARGING  GENERATOR  INSPECTION  


PROCEDURE

Hide 27330 1.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A117220

Check the rotor for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
100 A Type and 130 A Type
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 2.3 to 2.7 Ω

150 A Type
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.5 to 1.9 Ω


If the result is not as specified, replace the rotor assembly.



b.
A117221

Check if the rotor is grounded.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Slip ring - Rotor Always 10 kΩ or higher


If the result is not as specified, replace the rotor assembly.



c.

Check that the slip rings are not rough or scored.

If rough or scored, replace the rotor assembly.


d.
A117222E05
0.438,0.417 1.031,0.604 0.594,0.188 10 true Diameter

Using a vernier caliper, measure the slip ring diameter.

Standard diameter:

14.2 to 14.4 mm (0.559 to 0.567 in.)


Minimum diameter:

14.0 mm (0.551 in.)


If the diameter is less than the minimum, replace the rotor assembly.


Hide 27370 2.INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

A079305E02
0.619,0.394 1.113,0.601 0.494,0.207 10 Length

a.

Using a vernier caliper, measure the exposed brush length.

Standard exposed length:

10.5 mm (0.413 in.)


Minimum exposed length:

4.5 mm (0.177 in.)


If the exposed length is less than the minimum, replace the brush holder assembly.


Hide 27310B 3.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A156418

When rotating the bearing, check that there is no abnormal noise and that it rotates smoothly.

If necessary, replace the bearing.


Hide 27310B 4.REPLACE GENERATOR DRIVE END FRAME BEARING

a.
A156416

Remove the 4 screws and retainer plate.


b.
A156417E01
2.377,0.955 2.721,1.136 0.344,0.181 10 SST 1.673,1.377 2.333,1.042 false 2.333,1.042 1.68,0.979 false

Using SST and a hammer, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)


c.
A156419E01
2.872,0.516 3.203,0.707 0.331,0.190 10 SST 1.752,0.766 2.825,0.586 false 2.825,0.586 1.891,1.212 false

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


d.
A156416

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330A 5.INSPECT GENERATOR ROTOR BEARING

a.
A163064

When rotating the bearing, check that there is no abnormal noise and that it rotates smoothly.

If necessary, replace the generator rotor.