Home › Engine / Hybrid System › 3UR-FBE CHARGING › GENERATOR
RM27M0U _51 Engine / Hybrid System _049148 3UR-FBE CHARGING _0234380 GENERATOR A

3UR-FBE CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27330 1.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A156420

Place the drive end frame on the pulley.


b.

Install the rotor to the drive end frame.


Hide 27360 2.INSTALL GENERATOR COIL ASSEMBLY

a.
A156421

Place the generator washer on the rotor.


b.
A156422E01
1.776,0.645 2.515,0.388 false 2.565,0.299 2.902,0.481 0.337,0.182 10 SST

Using SST and a press, slowly press in the coil assembly.

SST
09285-76010  


c.
A156414

Install the 4 bolts.

Torque:
5.8 N*m (59 kgf*cm, 51 in.*lbf)


Hide 27370 3.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A163049

While pushing the 2 brushes toward the inside of the brush holder, insert a pin (diameter: 1.0 mm (0.0394 in.)) into the brush holder hole.


b.
A156423E01
2.769,0.258 3.061,0.446 0.292,0.188 10 Pin 1.791,0.863 2.657,0.344 false 2.649,0.344 2.734,0.344 false

Install the generator brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder.


Hide 27039 4.INSTALL GENERATOR REAR END COVER

a.
A156408

Install the terminal insulator to the generator rectifier end frame.

NOTICE:

Pay attention to the mounting orientation of the terminal insulator.



b.
A156407

Install the end cover with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 5.INSTALL GENERATOR PULLEY

A187035E07
3.073,1.188 3.073,0.573 false 2.427,1.542 2.427,1.302 2.427,1.302 2.833,0.719 false 0.906,1.344 1.219,1.563 0.313,0.219 10 true Turn 1.656,1.885 1.969,2.031 0.313,0.146 10 false Hold 2.083,1.583 2.635,1.729 0.552,0.146 10 false SST 1-B 2.74,1.208 3.292,1.354 0.552,0.146 10 false SST 1-A

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021


a.

Clamp the generator housing stay in a vise.


b.

Install the pulley onto the rotor shaft by tightening the pulley nut by hand.


c.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is secured to the rotor shaft.



d.
A187036E06
2.531,0.375 2.667,0.375 2.667,0.375 2.823,0.885 false 2,0.292 2.458,0.49 0.458,0.198 10 false SST 2 2.302,1.406 2.698,1.604 0.396,0.198 10 true Insert

Insert SST 2, and attach the pulley nut to SST 2.


e.
A187039E08
0.865,1.313 1.177,1.313 1.177,1.313 1.927,1.094 false 2.896,0.74 3.198,0.938 0.302,0.198 10 false Turn 1.698,1.771 1.979,1.958 0.281,0.188 10 true Hold 0.208,1.25 0.875,1.563 0.667,0.313 10 false Adjustable wrench

Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



f.

Remove the generator from SST 2.


g.
A187038E07
3.073,1.177 3.073,0.615 false 2.573,1.573 2.573,1.354 2.573,1.354 2.833,0.75 false 1.208,1.438 1.49,1.615 0.281,0.177 10 true Turn 1.896,1.646 2.208,1.854 0.313,0.208 10 true Hold 2.281,1.604 2.854,1.823 0.573,0.219 10 true SST 1-B 2.76,1.198 3.313,1.354 0.552,0.156 10 false SST 1-A

Turn SST 1-B, and remove SST 1-A and B.


h.

Turn the pulley and check that the pulley moves smoothly.