Home › Drivetrain › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 2WD)
RM27M0U _52 Drivetrain _049149 PROPELLER SHAFT _0234382 PROPELLER SHAFT ASSEMBLY(for 2WD) A

PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 2WD)  INSTALLATION  


PROCEDURE

Hide 1.MEASURE EXTENSION HOUSING AND DIFFERENTIAL FLANGE ANGLE

NOTICE:
·

Perform the inspection on a level surface.

·

Perform the inspection with the vehicle empty.

·

Perform the inspection with all wheels on the ground.



HINT:

As the extension housing and rear differential flange angles are necessary when measuring the installation angle of the propeller shaft, measure the angle of the extension housing and rear differential flange before installing the propeller shaft.


a.
C180329E03
0.101,0.059 0.311,0.234 0.210,0.175 10 *a 2.624,1.773 2.942,1.924 0.319,0.151 10 SST 2.574,1.849 1.866,1.849 false

Using SST, measure and record the angle of the extension housing flange (A).

SST
09370-50010  

Text in Illustration
*a Extension Housing Flange Angle: A


b.
C180330E02
0.092,0.045 0.322,0.182 0.230,0.137 10 *a 0.636,1.779 0.931,1.956 0.295,0.177 10 SST 0.997,1.875 1.479,1.875 false

Using SST, measure and record the angle of the rear differential flange (B).

SST
09370-50010  

Text in Illustration
*a Rear Differential Flange Angle: B


Hide 37100 2.TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

a.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.


b.

for 1UR-FE:

Remove SST from the transmission.

SST
09325-40010  


c.

for 3UR-FE:

Remove SST from the transmission.

SST
09325-60010  


d.

Insert the sleeve yoke into the transmission.


e.

w/o Bearing Washer:

i.
C158583

Temporarily install the center support bearing to the crossmember with the 2 mounting bolts.



f.

w/ Bearing Washer:

i.
C179315E03
1.688,2.448 2.125,2.448 false 1.281,2.927 2.292,2.927 false 1.469,3.219 2.292,3.219 false 1.135,2.844 1.354,3.01 0.219,0.167 10 false *1 1.531,2.354 1.74,2.5 0.208,0.146 10 false *a 1.313,3.135 1.531,3.292 0.219,0.156 10 false *2

Temporarily install the center support bearing to the crossmember with the 2 bearing washers and 2 mounting bolts.

Text in Illustration
*1 No. 2 Center Support Bearing Washer
*2 No. 1 Center Support Bearing Assembly
*a Frame



g.
C158582E03
2.091,1.799 2.283,1.955 0.192,0.156 10 *a 1.84,1.009 2.164,1.748 false 2.17,1.765 1.792,1.015 false

Align the matchmarks on the propeller shaft flange and differential flange.

Text in Illustration
*a Matchmark


h.

Connect the propeller shaft to the differential side, and install the 4 bolts and 4 nuts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 37100 3.TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

a.

With the vehicle empty and all 4 tires supported by a lift, or with the vehicle suspension in the full rebound position, adjust the center bearing so that dimension A (the distance from the front surface of the center bearing housing to the back surface of the intermediate shaft) is as shown in the chart below.

HINT:

Measure dimension A (the distance from the front surface of the center bearing housing to the back surface of the intermediate shaft) at 3 places and make adjustments so that the measured dimensions are equal.


C172056E03
1.281,3 1.281,3.396 false 1.281,3.396 2.083,3.396 false 1.74,1.083 1.531,1.083 false 1.531,1.083 0.938,1.75 false 2.125,3.333 2.323,3.49 0.198,0.156 10 false *b 1.781,1.021 1.979,1.156 0.198,0.135 10 false *a 5.417,0.333 5.615,0.51 0.198,0.177 10 false *c 5.385,2.104 5.594,2.292 0.208,0.188 10 false *d

Text in Illustration
*a Intermediate Shaft *b Dimension A
*c Tires supported and vehicle empty (When using drive-on type lift) *d Full rebound position (When using 2 post lift)
V100135

Front Side - -

Standard Dimension A:
Vehicle Model Dimension A
Tires supported and vehicle empty
(When using drive-on type lift)
Full rebound position
(When using 2 post lift)
UPK51L-CRTSKA 24.0 mm (0.945 in.) 16.0 mm (0.630 in.)
UPK51L-CRTSKA*1
UPK51L-PSTSKA 24.0 mm (0.945 in.) 16.0 mm (0.630 in.)
UPK51L-PSTSKA*1
USK51L-CRTLKA 23.0 mm (0.906 in.) 16.0 mm (0.630 in.)
USK51L-CRTLKA*1
USK51L-CRTSKA 23.0 mm (0.906 in.) 16.0 mm (0.630 in.)
USK51L-CRTSKA*1
USK51L-CRTSKA*2
USK51L-PSTLKA 24.0 mm (0.945 in.) 16.0 mm (0.630 in.)
USK51L-PSTLKA*1
USK51L-PSTSKA 24.0 mm (0.945 in.) 16.0 mm (0.630 in.)
USK51L-PSTSKA*1
USK51L-PSTSKA*2
USK51L-PSTZKA 24.0 mm (0.945 in.) 16.0 mm (0.630 in.)
USK51L-THTSKA 21.0 mm (0.827 in.) 16.0 mm (0.630 in.)
USK51L-THTSKA*1
USK52L-CHTSKA 21.0 mm (0.827 in.) 16.0 mm (0.630 in.)
USK52L-CHTSKA*1


*1: includes Off road package

*2: includes Off road pro package


b.
C160089E02
0.771,0.257 0.997,0.425 0.227,0.168 10 *a 1.879,0.162 2.090,0.317 0.211,0.155 10 *b 1.854,0.246 1.506,0.246 false 1.781,1.659 1.971,1.809 0.190,0.150 10 *c 1.856,1.09 1.856,1.642 false

Check that the center line of the bracket is at right angles to the shaft axial direction.

Text in Illustration
*a 90°
*b Bracket Center Line
*c Shaft Axial Direction


c.

Tighten the 2 mounting bolts.

Torque:
40 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 4.INSPECT PROPELLER SHAFT ANGLE

NOTICE:
·

Perform the inspection on a level surface.

·

Perform the inspection with the vehicle empty.

·

Perform the inspection with all wheels on the ground.



a.

Measure the No. 1 joint angle.

i.

Using SST, measure and record the angle of the intermediate shaft (C).

SST
09370-50010  

C180167E03
3.302,0.354 2.677,0.354 false 2.677,0.354 2.375,1.125 false 2.854,1.719 3.156,1.719 false 3.375,0.281 3.635,0.448 0.26,0.167 10 false *a 3.188,1.646 3.479,1.813 0.292,0.167 10 false SST

Text in Illustration
*a Intermediate Shaft Angle: C - -


ii.
C180168E02
1.205,0.119 1.400,0.277 0.194,0.158 10 *a 1.449,0.208 1.711,0.208 false 1.711,0.208 1.815,1.038 false

Subtract the angle of the extension housing flange (A) measured before installing the propeller shaft from the angle of the intermediate shaft (C) to calculate the No. 1 joint angle.

Text in Illustration
*a No. 1 Joint Angle

No. 1 joint angle:

Angle of intermediate shaft (C) - Angle of extension housing flange (A)


Measured Value (Reference):
Intermediate Shaft Angle Measured Value (C) Extension Housing Flange Angle Measured Value (A) No. 1 Joint Angle (Calculated Value)
(C) - (A)
3°15' (3.25°) 4°00' (4.00°) -0°45' (-0.75°)


HINT:
·

Using the following chart, check if the calculated No. 1 joint angle is within the specified value.

·

The tolerance is +/-0°60' (1.00°).



Standard No. 1 Joint Angle:
Vehicle Model No. 1 Joint Angle
UPK51L-CRTSKA 0°41' +/-0°60' (0.68° +/-1.00°)
UPK51L-CRTSKA*1
UPK51L-PSTSKA 0°41' +/-0°60' (0.68° +/-1.00°)
UPK51L-PSTSKA*1
USK51L-CRTLKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-CRTLKA*1
USK51L-CRTSKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-CRTSKA*1
USK51L-CRTSKA*2
USK51L-PSTLKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-PSTLKA*
USK51L-PSTSKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-PSTSKA*1
USK51L-PSTSKA*2
USK51L-PSTZKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-THTSKA 0°41' +/-0°60' (0.68° +/-1.00°)
USK51L-THTSKA*
USK52L-CHTSKA 0°58' +/-0°60' (0.97° +/-1.00°)
USK52L-CHTSKA*1 0°57' +/-0°60' (0.96° +/-1.00°)


*1: includes Off road package

*2: includes Off road pro package

If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").




b.

Measure the No. 2 joint angle.

i.

Using SST, measure and record the angle of the propeller shaft (D).

SST
09370-50010  

C180169E02
3.842,0.287 4.051,0.453 0.209,0.166 10 *a 3.778,0.352 3.432,0.352 false 3.432,0.352 3.089,1.119 false 4.292,1.754 4.583,1.892 0.291,0.138 10 SST 4.235,1.819 3.541,1.819 false

Text in Illustration
*a Propeller Shaft Angle: D - -


ii.

Subtract the angle of the propeller shaft (D) from the angle of the intermediate shaft (C) to calculate the No. 2 joint angle.

C180170E02
4.718,0.541 4.920,0.692 0.201,0.151 10 *a 4.689,0.612 4.325,0.612 false 4.325,0.612 3.92,1.197 false

Text in Illustration
*a No. 2 Joint Angle - -

No. 2 joint angle:

Angle of intermediate shaft (C) - Angle of propeller shaft (D)


Measured Value (Reference):
Intermediate Shaft Angle Measured Value (C) Propeller Shaft Angle Measured Value (D) No. 2 Joint Angle (Calculated Value)
(C) - (D)
3°15' (3.25°) 5°30' (5.50°) -2°15' (-2.25°)


HINT:
·

Using the following chart, check if the calculated No. 2 joint angle is within the specified value.

·

The tolerance is +/-0°60' (1.00°).



Standard No. 2 Joint Angle:
Vehicle Model No. 2 Joint Angle
UPK51L-CRTSKA -2°14' +/-0°60' (-2.24° +/-1.00°)
UPK51L-CRTSKA*1 -1°56' +/-0°60' (-1.93° +/-1.00°)
UPK51L-PSTSKA -1°52' +/-0°60' (-1.87° +/-1.00°)
UPK51L-PSTSKA*1 -1°56' +/-0°60' (-1.93° +/-1.00°)
USK51L-CRTLKA -2°02' +/-0°60' (-2.03° +/-1.00°)
USK51L-CRTLKA*1 -1°47' +/-0°60' (-1.78° +/-1.00°)
USK51L-CRTSKA -2°02' +/-0°60' (-2.03° +/-1.00°)
USK51L-CRTSKA*1 -1°47' +/-0°60' (-1.78° +/-1.00°)
USK51L-CRTSKA*2 -2°02' +/-0°60' (-2.03° +/-1.00°)
USK51L-PSTLKA -2°25' +/-0°60' (-2.42° +/-1.00°)
USK51L-PSTLKA*1 -2°06' +/-0°60' (-2.10° +/-1.00°)
USK51L-PSTSKA -2°25' +/-0°60' (-2.42° +/-1.00°)
USK51L-PSTSKA*1 -2°06' +/-0°60' (-2.10° +/-1.00°)
USK51L-PSTSKA*2 -2°25' +/-0°60' (-2.42° +/-1.00°)
USK51L-PSTZKA -2°11' +/-0°60' (-2.19° +/-1.00°)
USK51L-THTSKA -2°58' +/-0°60' (-2.97° +/-1.00°)
USK51L-THTSKA*1 -2°52' +/-0°60' (-2.87° +/-1.00°)
USK52L-CHTSKA -1°17' +/-0°60' (-1.28° +/-1.00°)
USK52L-CHTSKA*1 -0°51' +/-0°60' (-0.85° +/-1.00°)


*1: includes Off road package

*2: includes Off road pro package

If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").




c.

Measure the No. 3 joint angle.

i.

Subtract the angle of the rear differential flange (B) measured before installing the propeller shaft from the angle of the propeller shaft (D) to calculate the No. 3 joint angle.

C180171E02
4.188,0.648 4.378,0.804 0.190,0.156 10 *a 4.412,0.718 4.832,0.718 false 4.832,0.718 5.327,1.395 false

Text in Illustration
*a No. 3 Joint Angle - -

No. 3 joint angle:

Angle of propeller shaft (D) - Angle of rear differential flange (B)


Measured Value (Reference):
Propeller Shaft Angle Measured Value (D) Rear Differential Flange Angle Measured Value (B) No. 3 Joint Angle (Calculated Value)
(D) - (B)
5°30' (5.50°) 1°15' (1.25°) 4°15' (4.25°)


HINT:
·

Using the following chart, check if the calculated No. 3 joint angle is within the specified value.

·

The tolerance is +/-0°60' (1.00°).



Standard No. 3 Joint Angle:
Vehicle Model No. 3 Joint Angle
UPK51L-CRTSKA 3°31' +/-0°60' (3.52° +/-1.00°)
UPK51L-CRTSKA*1 3°14' +/-0°60' (3.23° +/-1.00°)
UPK51L-PSTSKA 3°40' +/-0°60' (3.67° +/-1.00°)
UPK51L-PSTSKA*1 3°43' +/-0°60' (3.72° +/-1.00°)
USK51L-CRTLKA 2°50' +/-0°60' (2.83° +/-1.00°)
USK51L-CRTLKA*1 2°34' +/-0°60' (2.57° +/-1.00°)
USK51L-CRTSKA 2°50' +/-0°60' (2.83° +/-1.00°)
USK51L-CRTSKA*1 2°34' +/-0°60' (2.57° +/-1.00°)
USK51L-CRTSKA*2 2°50' +/-0°60' (2.83° +/-1.00°)
USK51L-PSTLKA 4°12' +/-0°60' (4.20° +/-1.00°)
USK51L-PSTLKA*1 3°00' +/-0°60' (3.01° +/-1.00°)
USK51L-PSTSKA 4°12' +/-0°60' (4.20° +/-1.00°)
USK51L-PSTSKA*1 3°53' +/-0°60' (3.88° +/-1.00°)
USK51L-PSTSKA*2 4°12' +/-0°60' (4.20° +/-1.00°)
USK51L-PSTZKA 3°59' +/-0°60' (3.98° +/-1.00°)
USK51L-THTSKA 4°13' +/-0°60' (4.22° +/-1.00°)
USK51L-THTSKA*1 3°37' +/-0°60' (3.62° +/-1.00°)
USK52L-CHTSKA 3°17' +/-0°60' (3.28° +/-1.00°)
USK52L-CHTSKA*1 2°52' +/-0°60' (2.87° +/-1.00°)


*1: includes Off road package

*2: includes Off road pro package

If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").




Hide 5.ADJUST PROPELLER SHAFT ANGLE

HINT:

If the propeller shaft angle is outside the specification or there is vibration and noise, perform the propeller shaft adjustment using the following procedure.


a.

Adjust the No. 1, No. 2 and No. 3 joint angle.

i.

Support the propeller shaft with a jack.


ii.

Remove the 2 center bearing mounting bolts.


iii.

Slowly lower the jack, and disconnect the center bearing.


iv.

Select an appropriate center support bearing washer thickness from the table below, and obtain a washer set.

Standard Bearing Washer Thickness:
Thickness
2.0 mm (0.0787 in.)
4.5 mm (0.1772 in.)
6.5 mm (0.2559 in.)
9.0 mm (0.3543 in.)
11.0 mm (0.4331 in.)
13.5 mm (0.5315 in.)


HINT:
·

Each set contains 2 washers.

·

Using the washer set, perform the adjustment.

·

As a reference when selecting a bearing washer, the angle changes as follows for every 1.0 mm (0.0394 in.) change in bearing washer thickness.

Angle variation for every 1.0 mm (0.0394 in.) change in bearing washer thickness:
No. 1 joint angle:

0°04' (0.06°)

No. 2 joint angle:

0°07' (0.12°)

No. 3 joint angle:

0°04' (0.06°)






Hide 6.INSPECT FOR OIL LEAK