Home › Drivetrain › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 2WD)
RM27M0U _52 Drivetrain _049149 PROPELLER SHAFT _0234382 PROPELLER SHAFT ASSEMBLY(for 2WD) A

PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 2WD)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

a.
C158584E02
2.313,1.421 2.536,1.563 0.223,0.142 10 *a 1.958,0.637 2.377,1.37 false 2.382,1.384 2.083,0.661 false

Place matchmarks on the propeller shaft yoke and universal joint yoke.

Text in Illustration
*a Matchmark


b.
C160072

Using a brass bar and hammer, slightly tap in the 4 spider bearings.


c.

Using needle-nose pliers, remove the 4 snap rings from the grooves.


d.
C184732

Using a screwdriver, remove the 4 slingers of the spider bearing.


e.

Clamp the propeller shaft in a vise between aluminum plates.


f.
C293081E02
1.583,3.99 1.583,4.219 false 2.177,1.708 2.406,1.708 false 2.177,1.708 2.177,1.948 false 2.604,1.281 3.073,1.281 false 3.073,1.281 3.073,1.896 false 2.677,1.344 3.073,1.344 false 0.521,1.802 1.021,1.802 false 0.844,1.573 0.708,1.573 false 0.708,1.573 0.708,1.969 false 0.708,1.969 1,1.969 false 1.5,4.208 1.729,4.396 0.229,0.188 10 false *a 2.125,1.958 2.354,2.146 0.229,0.188 10 false *b 1.969,0.417 2.198,0.604 0.229,0.188 10 false *c 1.563,1.177 1.792,1.365 0.229,0.188 10 false *d 2.979,1.906 3.302,2.063 0.323,0.156 10 false SST 0.229,1.74 0.552,1.896 0.323,0.156 10 false SST

Using SST, press in spider bearing B until spider bearing A can be clamped in a vise.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09957-04010, 09958-04011)
09950-60010  (09951-00290)
09955-04100  

Text in Illustration
*a Spider Bearing A
*b Spider Bearing B
*c Turn
*d Hold

HINT:

Make sure the claws of SST are securely attached to the universal joint yoke.



g.

Clamp the protruding universal joint spider bearing in a vise.


h.
C183192E02
2.025,0.124 2.221,0.278 0.197,0.154 10 *a 1.986,0.208 1.742,0.208 false 1.742,0.208 1.658,0.69 false

Using a brass bar and hammer, tap the universal joint yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the intermediate shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



i.

Disconnect the intermediate shaft from the propeller shaft.


j.
C293082E02
2.521,1.76 2.521,1.969 false 3.052,1.083 3.052,1.885 false 3.042,1.083 2.635,1.083 false 3.042,1.25 2.677,1.25 false 0.813,1.667 0.417,1.667 false 0.573,1.396 0.573,1.396 false 0.573,1.396 0.479,1.396 false 0.479,1.396 0.479,1.833 false 0.479,1.833 0.771,1.833 false 2.448,1.958 2.667,2.125 0.219,0.167 10 false *a 1.854,0.198 2.073,0.365 0.219,0.167 10 false *b 1.469,1.021 1.688,1.188 0.219,0.167 10 false *c 2.917,1.896 3.229,2.052 0.313,0.156 10 false SST 0.125,1.594 0.438,1.75 0.313,0.156 10 false SST

Using SST, pull out the universal joint spider bearing from the propeller shaft yoke.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the propeller shaft yoke.



k.

Clamp the protruding universal joint spider bearing in a vise.


l.
C183753E02
2.284,0.221 2.451,0.377 0.167,0.155 10 *a 2.247,0.303 2.094,0.303 false 2.095,0.306 1.798,0.476 false

Using a brass bar and hammer, tap the propeller shaft yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the propeller shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



m.

Remove the spider from the propeller shaft.


Hide 37230 2.REMOVE NO. 1 CENTER SUPPORT BEARING ASSEMBLY

a.

Fix the center support bearing in a vise.


b.

Using a chisel and hammer, loosen the staked part of the lock nut. Then remove the lock nut.


c.
C158515E02
0.704,0.479 0.867,0.626 0.163,0.147 10 *a 1.73,1.094 0.921,0.578 false 0.921,0.578 1.73,1.007 false

Place matchmarks on the joint yoke and shaft.

Text in Illustration
*a Matchmark


d.

Using a brass bar and hammer, tap the end of the intermediate shaft to remove the joint yoke, washer and center support bearing from the intermediate shaft.


Hide 3.REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same removal procedure for both the sleeve yoke side and flange yoke side universal joint spider bearings.


a.
C160567E02
0.064,0.181 0.276,0.360 0.212,0.179 10 *a 1.845,0.184 2.044,0.351 0.198,0.168 10 *b 0.481,1.82 0.688,1.975 0.207,0.156 10 *c 0.637,1.198 0.588,1.769 false 0.588,1.769 0.511,1.168 false 2.241,1.826 2.434,1.982 0.193,0.156 10 *c 2.516,1.189 2.345,1.797 false 2.345,1.797 2.378,1.164 false

Place matchmarks on the flange yoke and shaft, and the sleeve yoke and shaft.

Text in Illustration
*a for Sleeve Yoke Side
*b for Flange Yoke Side
*c Matchmark


b.
C160077

Using a brass bar and hammer, slightly tap in the spider bearing.


c.

Using needle-nose pliers, remove the snap ring from the grooves.

HINT:

Remove the snap ring on the opposite side using the same procedure.



d.
C184732

Using a screwdriver, remove the 4 slingers of the spider bearing.


e.

Clamp the shaft in a vise between aluminum plates.


f.
C293083E02
2.156,0.875 2.417,0.333 false 2.417,0.333 2.635,0.333 false 0.792,2.26 1.708,2.74 false 1.042,2.74 1.708,2.74 false 0.76,2.76 1.583,3 false 1.635,2.906 1.854,3.094 0.219,0.188 10 false *a 0.823,0.552 1.042,0.74 0.219,0.188 10 false *b 0.813,1.281 1.031,1.469 0.219,0.188 10 false *c 2.688,0.25 3.021,0.417 0.333,0.167 10 false SST 1.781,2.667 2.115,2.833 0.333,0.167 10 false SST

Using SST, pull out the universal joint spider bearing from the shaft.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the shaft's universal joint yoke.



g.

Clamp the protruding universal joint spider bearing in a vise.


h.
C179266E02
1.897,2.361 2.085,2.535 0.188,0.173 10 *a 1.736,2.447 1.464,2.55 false 1.736,2.447 1.879,2.447 false

Using a brass bar and hammer, tap the shaft yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



i.
C293084E02
1,2.354 2.219,2.823 false 1.25,2.833 2.219,2.823 false 0.938,2.823 1.781,3.073 false 2.802,1.188 2.802,0.771 false 2.802,0.771 2.885,0.771 false 1.833,3.021 2.052,3.198 0.219,0.177 10 false *a 1.177,0.615 1.385,0.792 0.208,0.177 10 false *b 0.438,1.156 0.646,1.333 0.208,0.177 10 false *c 2.927,0.698 3.25,0.854 0.323,0.156 10 false SST 2.281,2.76 2.583,2.906 0.302,0.146 10 false SST

Using SST, pull out the universal joint spider bearing from the sleeve yoke.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the sleeve yoke.



j.
C179270E03
0.958,2.458 0.521,2.365 false 0.344,2.271 0.531,2.438 0.188,0.167 10 false *a

Clamp the protruding universal joint spider bearing in a vise.


k.

Using a brass bar and hammer, tap the sleeve yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



l.

Remove the spider from the sleeve yoke.