Home › Drivetrain › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 2WD)
RM27M0U _52 Drivetrain _049149 PROPELLER SHAFT _0234382 PROPELLER SHAFT ASSEMBLY(for 2WD) A

PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 2WD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same installation procedure for both the sleeve yoke side and flange yoke side universal joint spider bearings.


a.
C134387

Apply MP grease to a new spider and 4 new bearings.

NOTICE:

Be careful not to apply too much grease.



b.
C160084E01
1.24,0.979 1.373,1.116 0.133,0.137 10 A 1.695,0.979 1.809,1.128 0.114,0.149 10 B

Measure dimension A between the snap ring grooves.


c.

Install the 4 spider bearings to the spider journal portions, and then measure dimension B of the universal joint.

NOTICE:

When measuring dimension B, fix the spider and spider bearings in a vise and hold them firmly together.



d.
G038874

Select snap rings to make dimensions A and B the same.

Snap Ring Type for Steel Yoke:
Color Thickness
Purple 1.46 mm (0.0574 in.)
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)
Blue 1.64 mm (0.0646 in.)


Snap Ring Type for Aluminum Yoke:
Color Thickness
Black 1.52 mm (0.0598 in.)
Black 1.54 mm (0.0606 in.)
Black 1.57 mm (0.0618 in.)
Black 1.62 mm (0.0638 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.




e.

Temporarily install the spider and 2 universal joint spider bearings into the sleeve yoke.


f.
C293118E02
2.688,1.792 3.01,1.792 false 2.573,1.281 2.896,1.281 false 2.656,1.385 2.781,1.385 false 2.781,1.385 2.781,1.281 false 0.99,3.021 0.667,3.021 false 0.667,3.021 0.667,1.969 false 0.667,1.969 0.948,1.969 false 0.938,2.479 0.458,2.479 false 1.219,1.438 1.219,1.073 false 1.219,1.073 0.708,1.073 false 1,1.323 1,1.073 false 3.052,1.708 3.24,1.875 0.188,0.167 10 false *a 0.219,1.635 0.406,1.802 0.188,0.167 10 false *c 0.698,0.333 0.885,0.5 0.188,0.167 10 false *b 2.917,1.198 3.24,1.354 0.323,0.156 10 false SST 0.167,2.396 0.49,2.552 0.323,0.156 10 false SST 0.406,0.99 0.729,1.146 0.323,0.156 10 false SST

Using SST, press the universal joint spider bearing into the universal joint sleeve yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Confirm that the universal joint spider moves smoothly while pressing in the bearing.



g.
G038875

Using needle-nose pliers, install the previously selected snap ring into the groove of the yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



h.

Temporarily install the spider and 2 universal joint spider bearings into the shaft yoke.


i.
C293085E02
2.802,1.365 3.042,1.365 false 2.698,0.927 2.927,0.927 false 2.781,1.01 2.854,1.01 false 2.854,1.01 2.854,0.927 false 0.979,2.948 1.458,2.948 false 0.927,1.531 1.24,1.531 false 3.073,1.281 3.26,1.448 0.188,0.167 10 false *a 2.948,0.844 3.26,1 0.313,0.156 10 false SST 0.396,1.073 0.583,1.24 0.188,0.167 10 false *c 0.76,0.396 0.948,0.563 0.188,0.167 10 false *b 1.5,2.865 1.813,3.021 0.313,0.156 10 false SST 0.646,1.448 0.958,1.604 0.313,0.156 10 false SST

Using SST, press the universal joint spider bearing into the shaft yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:
·

Position SST (09336-16010) so that the cutout faces the shaft tube.

·

Confirm that the universal joint spider moves smoothly while pressing in the bearing.




j.

Using needle-nose pliers, install the previously selected snap ring into the groove on the shaft yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



Hide 37230 2.INSTALL NO. 1 CENTER SUPPORT BEARING ASSEMBLY

a.

Coat the splines of the intermediate shaft with MP grease.


b.
C293097

Install the center support bearing to the intermediate shaft.

Text in Illustration
V100135

Front


c.
C158515E03
0.695,0.457 0.881,0.604 0.186,0.147 10 *a 1.73,1.094 0.921,0.578 false 0.921,0.578 1.73,1.007 false

Align the matchmarks on the joint yoke and intermediate shaft.

Text in Illustration
*a Matchmark


d.

Install the washer.


e.

Clamp the yoke in a vise, and press the bearing into position by installing a new lock nut.

Torque:
128 N*m (1300 kgf*cm, 94 ft.*lbf)


f.

Loosen the lock nut.


g.

Tighten the lock nut again.

Torque:
128 N*m (1300 kgf*cm, 94 ft.*lbf)


h.

Using a chisel and hammer, stake the lock nut.


Hide 3.INSTALL PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

a.
C134387

Apply MP grease to a new spider and 4 new bearings.

NOTICE:

Be careful not to apply too much grease.



b.
C160084E01
1.24,0.979 1.373,1.116 0.133,0.137 10 A 1.695,0.979 1.809,1.128 0.114,0.149 10 B

Measure dimension A between the snap ring grooves.


c.

Install the 4 spider bearings to the spider journal portions, and then measure dimension B of the universal joint.

NOTICE:

When measuring dimension B, fix the spider and spider bearings in a vise and hold them firmly together.



d.
G038874

Select snap rings to make dimensions A and B the same.

Snap Ring Type for Steel Yoke:
Color Thickness
Purple 1.46 mm (0.0574 in.)
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)
Blue 1.64 mm (0.0646 in.)


Snap Ring Type for Aluminum Yoke:
Color Thickness
Black 1.52 mm (0.0598 in.)
Black 1.54 mm (0.0606 in.)
Black 1.57 mm (0.0618 in.)
Black 1.62 mm (0.0638 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.




e.

Temporarily install the universal joint spider and 2 universal joint spider bearings into the propeller shaft yoke.


f.
C293086E02
2.583,1.302 2.688,1.094 false 2.688,1.094 2.813,1.094 false 2.646,1.365 2.688,1.094 false 2.688,1.813 2.979,1.813 false 0.875,2.844 0.74,2.844 false 0.74,2.844 0.74,2.156 false 0.854,2.156 0.469,2.156 false 0.833,2.385 0.74,2.385 false 1.073,1.479 1.073,1.115 false 1.073,1.115 0.656,1.115 false 0.917,1.354 0.917,1.115 false 2.854,1.01 3.177,1.167 0.323,0.156 10 false SST 3.01,1.719 3.188,1.875 0.177,0.156 10 false *a 0.219,1.771 0.396,1.927 0.177,0.156 10 false *c 0.792,0.375 0.969,0.531 0.177,0.156 10 false *b 0.083,2.083 0.406,2.24 0.323,0.156 10 false SST 0.26,1.021 0.583,1.177 0.323,0.156 10 false SST

Using SST, press the universal joint spider bearing into the propeller shaft yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Confirm that the universal joint spider moves smoothly while pressing in the bearing.



g.
G038875

Using needle-nose pliers, install the previously selected snap ring into the groove of the yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



h.

Align the matchmarks on the propeller shaft yoke and universal joint yoke, and temporarily install the spider and 2 universal joint spider bearings into the universal joint yoke.


i.
C293087E02
3,2.167 2.729,2.167 false 2.625,1.76 2.781,1.583 false 2.781,1.583 2.885,1.583 false 2.708,1.833 2.781,1.583 false 0.583,2.802 0.583,3.302 false 0.583,3.302 1.104,3.302 false 1.021,3.125 0.583,3.125 false 1.104,2.802 0.458,2.802 false 1.313,1.865 1.313,1.51 false 1.313,1.51 0.802,1.51 false 1.115,1.75 1.115,1.51 false 3.031,2.063 3.26,2.292 0.229,0.229 10 false *a 0.208,2.104 0.438,2.333 0.229,0.229 10 false *c 0.594,1.052 0.823,1.281 0.229,0.229 10 false *b 2.927,1.5 3.26,1.656 0.333,0.156 10 false SST 0.073,2.719 0.385,2.875 0.313,0.156 10 false SST 0.396,1.427 0.708,1.583 0.313,0.156 10 false SST

Using SST, press the universal joint spider bearing into the universal joint yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold


j.

Using needle-nose pliers, install the previously selected snap ring into the groove on the universal joint yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



Hide 4.INSPECT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

a.
C158513

Check the spider bearings for wear and damage.


b.

Measure each spider bearing's axial play by turning the yoke while holding the shaft tightly.

Maximum bearing axial play:

0.05 mm (0.00197 in.)